Data Sheet No. PD 10027D Replaced by PVR13N Series PVR13 Microelectronic Power IC Dual-Pole, 400mA, 0-100V AC/DC General Description Features The PVR13 Photovoltaic Relay is a dual-pole, normally BOSFET Power IC open solid state replacement for electro-mechanical 10 relays. It utilizes as an output switch a unique 10 Operations bidirectional (AC or DC) MOSFET power IC termed 300sec Operating Time a BOSFET. The BOSFET is controlled by a photo- 0.2Volt Thermal Offset voltaic generator of novel construction, which is 5 milliwatts Pick-Up Power energized by radiation from a dielectrically isolated light emitting diode (LED). 1000V/sec dv/dt The PVR overcomes the limitations of reed relays by Bounce-Free offering the solid state advantages of long life, high 16-pin DIP Package operating speed, low pick-up power, bounce-free -40C to 85C operation, low thermal voltages and miniaturization. These advantages allow product improvement and design innovations in many applications such as process control, multiplexing, telecommunications, automatic test equipment and data acquisition. The PVR can switch analog signals from thermo- couple level to 100 volts peak AC or DC polarity. Signal frequencies into the RF range are easily controlled and switching rates up to 5kHz are achiev- able. The extremely small thermally generated offset voltages allow increased measurement accuracies. Unique silicon technology developed by International Rectifier forms the heart of the PVR. The monolithic BOSFET contains a bidirectional N-channel power MOSFET output structure. In addition, this power IC chip has input circuitry for fast turn-off and gate protection functions. This section of the BOSFET chip utilizes both bipolar and MOS technology to form NPN transistors, P-channel MOSFETs, resistors, Part Identification diodes and capacitors. Part Number Operating Off-State The photovoltaic generator similarly utilizes a unique Voltage (AC/DC) Resistance International Rectifier alloyed multijunction structure. 8 PVR1300 10 Ohms The excellent current conversion efficiency of this 0 100V technique results in the very fast response of the 10 PVR1301 10 Ohms PVR microelectronic power IC relay. This advanced semiconductor technology has cre- ated a radically new control device. Designers can now develop switching systems to new standards of (BOSFET is a trademark of International Rectifier) electrical performance and mechanical compactness. Replaced by PVR13N Electrical Specifications (-40C T +85C unless otherwise specified) A INPUT CHARACTERISTICS A Connection C Connection Units Minimum Control Current (see figure 1) DC For 100mA Continuous Load Current 1 1 mA 25C For 400mA Continuous Load Current 10 5 mA 25C For 100mA Continuous Load Current 10 7 mA 85C Minimum Turn-Off Current 10 A(DC) Minimum Turn-Off Voltage 0.6 V(DC) Control Current Range (Caution: current limit input LED. See figure 6) 2.0 to 25 mA(DC) Maximum Reverse Voltage 7.0 V(DC) OUTPUT CHARACTERISTICS A Connection C Connection Units Operating Voltage Range 100 100 V (peak) Maxiumum Load Current 40C (see figure 1) 400 700 mA(DC) Response Time 25C (see figure 7) Maximum T 12mA Control, 100 mA Load, 100 V 300 s (on) DC Maximum T 12mA Control, 100 mA Load, 100 V 50 s DC (off) Max. On-state Resistance 25C (Pulsed) (figure 2) 100 mA Load, 12mA Control 5.0 1.5 8 Minimum Off-state Resistance 25C 80 V PVR1300 10 DC 10 PVR1301 10 Maximum Thermal Offset Voltage 5.0mA Control 0.2 volts Minimum Off-State dv/dt 1000 V/s Output Capacitance (see figure 10) 20 40 pF 20VDC GENERAL CHARACTERISTICS (PVR1300 and PVR1301) Units Dielectric Strength: Input-Output 1500 V RMS 12 Insulation Resistance: Input-Output 500V 10 25C - 50% RH DC Maximum Capacitance: Input-Output 1.0 pF Lead Temperature (1.6mm below seating plane for 10 seconds) 260 C Ambient Temperature Range: Operating -40 to +85 C Storage -40 to +100 2