74LVC273DB,118 Nexperia

74LVC273 Octal D-type flip-flop with reset positive-edge trigger Rev. 8 31 August 2021 Product data sheet 1. General description The 74LVC273 is an octal positive-edge triggered D-type flip-flop. The device features clock (CP) and master reset (MR) inputs. The outputs Qn will assume the state of their corresponding D inputs that meet the set-up and hold time requirements on the LOW-to-HIGH clock (CP) transition. A LOW on MR forces the outputs LOW independently of clock and data inputs. Inputs can be driven from either 3.3 V or 5 V devices. This feature allows the use of these devices as translators in mixed 3.3 V and 5 V environments. Schmitt-trigger action at all inputs makes the circuit tolerant of slower input rise and fall times. 2. Features and benefits Wide supply voltage range from 1.2 V to 3.6 V Overvoltage tolerant inputs to 5.5 V CMOS low power consumption Direct interface with TTL levels Output drive capability 50 transmission lines at +85 C Complies with JEDEC standard: JESD8-7A (1.65 V to 1.95 V) JESD8-5A (2.3 V to 2.7 V) JESD8-C/JESD36 (2.7 V to 3.6 V) ESD protection: HBM JESD22-A114F exceeds 2000 V MM JESD22-A115-B exceeds 200 V CDM JESD22-C101E exceeds 1000 V Specified from -40 C to +85 C and -40 C to +125 C 3. Ordering information Table 1. Ordering information Type number Package Temperature range Name Description Version 74LVC273D -40 C to +125 C SO20 plastic small outline package 20 leads SOT163-1 body width 7.5 mm 74LVC273PW -40 C to +125 C TSSOP20 plastic thin shrink small outline package 20 leads SOT360-1 body width 4.4 mm 74LVC273BQ -40 C to +125 C DHVQFN20 plastic dual in-line compatible thermal enhanced SOT764-1 very thin quad flat package no leads 20 terminals body 2.5 4.5 0.85 mmNexperia 74LVC273 Octal D-type flip-flop with reset positive-edge trigger 4. Functional diagram 11 CP C1 1 R MR 11 3 2 1D CP D0 Q0 3 2 D0 Q0 4 5 D1 Q1 4 5 D1 Q1 7 6 7 6 D2 Q2 D2 Q2 8 9 8 9 D3 Q3 D3 Q3 13 12 13 12 D4 Q4 D4 Q4 14 15 14 15 D5 Q5 D5 Q5 17 16 D6 Q6 17 16 D6 Q6 18 19 D7 Q7 18 19 MR D7 Q7 1 mna763 mna764 Fig. 1. Logic symbol Fig. 2. IEC logic symbol 5. Pinning information 5.1. Pinning 74LVC273 terminal 1 index area 2 19 Q0 Q7 D0 3 18 D7 D1 4 17 D6 74LVC273 Q1 5 16 Q6 1 20 MR V Q2 6 15 Q5 CC 2 19 Q0 Q7 7 14 D2 D5 3 18 D0 D7 D3 8 (1) 13 D4 GND 4 17 D1 D6 Q3 9 12 Q4 5 16 Q1 Q6 6 15 Q2 Q5 7 14 001aad094 D2 D5 8 13 D3 D4 Transparent top view 9 12 Q3 Q4 (1) This is not a ground pin. There is no electrical or 10 11 GND CP mechanical requirement to solder the pad. In case 001aad093 soldered, the solder land should remain floating or connected to GND. Fig. 3. Pin configuration for SOT163-1 (SO20) and SOT360-1 (TSSOP20) Fig. 4. Pin configuration for SOT764-1 (DHVQFN20) 74LVC273 All information provided in this document is subject to legal disclaimers. Nexperia B.V. 2021. All rights reserved Product data sheet Rev. 8 31 August 2021 2 / 14 GND 10 1 MR CP 11 20 V CC