Single-Channel: 6N137, HCPL2601, HCPL2611 Dual-Channel: HCPL2630, HCPL2631 High Speed 10MBit/s Logic Gate Optocouplers January 2011 Single-Channel: 6N137, HCPL2601, HCPL2611 Dual-Channel: HCPL2630, HCPL2631 High Speed 10MBit/s Logic Gate Optocouplers Features Description Very high speed 10 MBit/s The 6N137, HCPL2601, HCPL2611 single-channel and HCPL2630, HCPL2631 dual-channel optocouplers Superior CMR 10 kV/s consist of a 850 nm AlGaAS LED, optically coupled to a Double working voltage-480V very high speed integrated photo-detector logic gate with Fan-out of 8 over -40C to +85C a strobable output. This output features an open collec- Logic gate output tor, thereby permitting wired OR outputs. The coupled Strobable output parameters are guaranteed over the temperature range Wired OR-open collector of -40C to +85C. A maximum input signal of 5mA will U.L. recognized (File E90700) provide a minimum output sink current of 13mA (fan out of 8). Applications An internal noise shield provides superior common Ground loop elimination mode rejection of typically 10kV/s. The HCPL2601 and LSTTL to TTL, LSTTL or 5-volt CMOS HCPL2631 has a minimum CMR of 5kV/s. The Line receiver, data transmission HCPL2611 has a minimum CMR of 10kV/s. Data multiplexing Switching power supplies Pulse transformer replacement Computer-peripheral interface Schematics Package Outlines 8 V N/C 1 8 + V CC 1 8 CC 1 V F1 V + 2 7 V E 2 7 01 V F 8 8 3 6 V V O 3 6 02 1 1 V F2 GND N/C 4 5 GND + 4 5 Truth Table (Positive Logic) Input Enable Output H H L 6N137 HCPL2630 L H H HCPL2601 HCPL2631 H L H HCPL2611 L L H (1) A 0.1F bypass capacitor must be connected between pins 8 and 5 . H NC L L NC H 2005 Fairchild Semiconductor Corporation www.fairchildsemi.com 6N137, HCPL2601, HCPL2611, HCPL2630, HCPL2631 Rev. 1.0.8Single-Channel: 6N137, HCPL2601, HCPL2611 Dual-Channel: HCPL2630, HCPL2631 High Speed 10MBit/s Logic Gate Optocouplers Absolute Maximum Ratings (T = 25C unless otherwise specied) A Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Value Units T Storage Temperature -55 to +125 C STG Operating Temperature -40 to +85 C T OPR T Lead Solder Temperature (for wave soldering only)* 260 for 10 sec C SOL EMITTER I DC/Average Forward Single Channel 50 mA F Input Current Dual Channel (Each Channel) 30 V Enable Input Voltage Not to Exceed Single Channel 5.5 V E V by more than 500mV CC V Reverse Input Voltage Each Channel 5.0 V R Power Dissipation Single Channel 100 mW P I Dual Channel (Each Channel) 45 DETECTOR V Supply Voltage 7.0 V CC (1 minute max) I Output Current Single Channel 50 mA O Dual Channel (Each Channel) 50 Output Voltage Each Channel 7.0 V V O P Collector Output Single Channel 85 mW O Power Dissipation Dual Channel (Each Channel) 60 *For peak soldering reow, please refer to the Reow Prole on page 11. Recommended Operating Conditions The Recommended Operating Conditions table denes the conditions for actual device operation. Recommended operating conditions are specied to ensure optimal performance to the datasheet specications. Fairchild does not recommend exceeding them or designing to absolute maximum ratings. Symbol Parameter Min. Max. Units I Input Current, Low Level 0 250 A FL Input Current, High Level *6.3 15 mA I FH V Supply Voltage, Output 4.5 5.5 V CC V Enable Voltage, Low Level 0 0.8 V EL Enable Voltage, High Level 2.0 V V V EH CC T Low Level Supply Current -40 +85 C A NFan Out (TTL load) 8 *6.3mA is a guard banded value which allows for at least 20% CTR degradation. Initial input current threshold value is 5.0mA or less. 2005 Fairchild Semiconductor Corporation www.fairchildsemi.com 6N137, HCPL2601, HCPL2611, HCPL2630, HCPL2631 Rev. 1.0.8 2