Industrial Inductive Load Driver NUD3160, SZNUD3160 This microintegrated part provides a single component solution to switch inductive loads such as relays, solenoids, and small DC motors without the need of a freewheeling diode. It accepts logic level www.onsemi.com inputs, thus allowing it to be driven by a large variety of devices including logic gates, inverters, and microcontrollers. MARKING DIAGRAMS Features 3 SOT23 JW8 M Provides Robust Interface between D.C. Relay Coils and Sensitive CASE 318 1 Logic STYLE 21 2 Capable of Driving Relay Coils Rated up to 150 mA at 12 V, 24 V JW8 = Specific Device Code or 48 V M = Date Code Replaces 3 or 4 Discrete Components for Lower Cost = PbFree Package (Note: Microdot may be in either location) Internal Zener Eliminates Need for FreeWheeling Diode Meets Load Dump and other Automotive Specs SC74 SZ Prefix for Automotive and Other Applications Requiring Unique JW8 M CASE 318F 6 Site and Control Change Requirements AECQ101 Qualified and STYLE 7 1 PPAP Capable JW8 = Specific Device Code These are PbFree Devices M = Date Code = PbFree Package Typical Applications (Note: Microdot may be in either location) Automotive and Industrial Environment Drives Window, Latch, Door, and Antenna Relays ORDERING INFORMATION Device Package Shipping Benefits NUD3160LT1G SOT23 3000 / Tape & Reduced PCB Space (PbFree) Reel Standardized Driver for Wide Range of Relays SZNUD3160LT1G SOT23 3000 / Tape & (PbFree) Reel Simplifies Circuit Design and PCB Layout NUD3160DMT1G SC74 3000 / Tape & Compliance with Automotive Specifications (PbFree) Reel SZNUD3160DMT1G SC74 3000 / Tape & (PbFree) Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. Drain (3) Drain (6) Drain (3) Gate (1) Gate (2) Gate (5) 10 k 10 k 10 k 100 k 100 k 100 k Source (2) Source (1) Source (4) CASE 318 CASE 318F Figure 1. Internal Circuit Diagrams Semiconductor Components Industries, LLC, 2003 1 Publication Order Number: December, 2020 Rev. 8 NUD3160/DNUD3160, SZNUD3160 MAXIMUM RATINGS (T = 25C unless otherwise specified) J Symbol Rating Value Unit V DraintoSource Voltage Continuous (T = 125C) 60 V DSS J V GatetoSource Voltage Continuous (T = 125C) 12 V GSS J I Drain Current Continuous (T = 125C) mA D J Minimum copper, double sided board, T = 80C A 158 SOT23 157 SC74 Single device driven 132 ea SC74 Both devices driven 2 1 in copper, double sided board, T = 25C A SOT23 272 SC74 Single device driven 263 SC74 Both devices driven 230 ea E Single Pulse DraintoSource Avalanche Energy 200 mJ Z (For Relays Coils/Inductive Loads of 80 or Higher) (T Initial = 85C) J P Peak Power Dissipation, DraintoSource (Notes 1 and 2) 20 W PK (T Initial = 85C) J E Load Dump Pulse, DraintoSource (Note 3) 60 V LD1 R = 0.5 , T = 300 ms) SOURCE (For Relays Coils/Inductive Loads of 80 or Higher) (T Initial = 85C) J E Inductive Switching Transient 1, DraintoSource 100 V LD2 (Waveform: R = 10 , T = 2.0 ms) SOURCE (For Relays Coils/Inductive Loads of 80 or Higher) (T Initial = 85C) J E Inductive Switching Transient 2, DraintoSource 300 V LD3 (Waveform: R = 4.0 , T = 50 s) SOURCE (For Relays Coils/Inductive Loads of 80 or Higher) (T Initial = 85C) J RevBat Reverse Battery, 10 Minutes (DraintoSource) 14 V (For Relays Coils/Inductive Loads of 80 or more) DualVolt Dual Voltage Jump Start, 10 Minutes (DraintoSource) 28 V ESD Human Body Model (HBM) 2000 V According to EIA/JESD22/A114 Specification Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. www.onsemi.com 2