DATASHEET EEPROM PROGRAMMABLE CLOCK GENERATOR IDT5V49EE702 Description Features The IDT5V49EE702 is a programmable clock generator Four internal PLLs intended for high performance data-communications, Internal non-volatile EEPROM telecommunications, consumer, and networking 2 Fast (400kHz) mode I C serial interface applications. There are four internal PLLs, each individually programmable, allowing for four unique non-integer-related Input frequency range: 1 MHz to 200 MHz frequencies. The frequencies are generated from a single Output frequency range: 4.9 kHz to 500 MHz reference clock. The reference clock can come from one of Reference crystal input with programmable linear load the two redundant clock inputs. Automatic or manual capacitance switchover function allows any one of the redundant clocks to be selected during normal operation. Crystal frequency range: 8 MHz to 50 MHz The IDT5V49EE702 is in-system, programmable and can Three independently controlled VDDO (1.8V - 3.3V) 2 be programmed through the use of I C interface. An Each PLL has a 7-bit reference divider and a 12-bit internal EEPROM allows the user to save and restore the feedback-divider configuration of the device without having to reprogram it on 8-bit output-divider blocks power-up. Fractional division capability on one PLL Each of the four PLLs has an 7-bit reference divider and a Two of the PLLs support spread spectrum generation 12-bit feedback divider. This allows the user to generate capability four unique non-integer-related frequencies. The PLL loop bandwidth is programmable to allow the user to tailor the I/O Standards: PLL response to the application. For instance, the user can Outputs - 1.8 - 3.3 V LVTTL/ LVCMOS tune the PLL parameters to minimize jitter generation or to maximize jitter attenuation. Spread spectrum generation Outputs - LVPECL, LVDS and HCSL and/or fractional divides are allowed on two of the PLLs. Inputs - 3.3 V LVTTL/ LVCMOS There are a total of five 8-bit output dividers. Each output Programmable slew rate control bank can be configured to support LVTTL, LVPECL, LVDS Programmable loop bandwidth or HCSL logic levels. Out0 (Output 0) supports LVTTL standard only. The outputs are connected to the PLLs via a Programmable output inversion to reduce bimodal jitter switch matrix. The switch matrix allows the user to route the Redundant clock inputs with auto and manual switchover PLL outputs to any output bank. This feature can be used to options simplify and optimize the board layout. In addition, each Individual output enable/disable output s slew rate and enable/disable function is programmable. Power-down mode 3.3V core V DD Available in VFQFPN package -40 to +85 C Industrial Temp operation IDT EEPROM PROGRAMMABLE CLOCK GENERATOR 1 IDT5V49EE702 REV N 071015IDT5V49EE702 EEPROM PROGRAMMABLE CLOCK GENERATOR CLOCK SYNTHESIZER Functional Block Diagram S R OUT0 C XIN/REF 0 XOUT S S1 PLL0 (SS) R /DIV1 C OUT1 1 S CLKIN R PLL1 /DIV2 OUT2 C 2 CLKSEL PLL2 S S3 R /DIV3 C PLL3 (SS) OUT3 3 S R SD/OE /DIV6 OUT6 C 6 SDA Control S OUT5 Logic SCL R /DIV5 C OUT5 5 SEL 2:0 1. OUT1 & OUT2, OUT3 & OUT6, and OUT5 & OUT5 pairs can be configured to be LVDS, LVPECL or HCSL, or two single-ended LVTTL outputs. 2. CLKIN, CLKSEL, SD/OE and SEL 2:0 have pull down resistors. IDT EEPROM PROGRAMMABLE CLOCK GENERATOR 2 IDT5V49EE702 REV N 071015