DATASHEET
HA-5104/883
FN3710
Rev 1.00
Low Noise, High Performance, Quad Operational Amplifier
April 2002
Features Description
This Circuit is Processed in Accordance to MIL-STD- Low noise and high performance are key words describing
883 and is Fully Conformant Under the Provisions of the unity gain stable HA-5104/883. This general purpose
Paragraph 1.2.1. quad amplifier offers an array of dynamic specifications
including 1V/s slew rate (min), and 8MHz bandwidth (typ).
Low Input Noise Voltage Density at 1kHz . .6nV/Hz (Max)
Complementing these outstanding parameters are very low
4.3nV/ Hz (Typ)
noise specifications of 4.3nV/Hz at 1kHz (typ) or 6nV/Hz
(max).
Slew Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1V/ s (Min)
3V/ s (Typ)
Fabricated using the Intersil standard high frequency D.I.
process, these operational amplifiers also offer excellent
Unity Gain Bandwidth . . . . . . . . . . . . . . . . . 8MHz (Typ)
input specifications such as 2.5mV (max) offset voltage and
High Open Loop Gain (Full Temp). . . . . . 100kV/V (Min)
75nA (max) offset current. Complementing these specifica-
250kV/V (Typ)
tions are 100dB (min) open loop gain and 55dB channel sep-
aration (min). Economically, the HA-5104/883 also
High CMRR, PSRR (Full Temp) . . . . . . . . . . 86dB (Min)
consumes a very moderate amount of power (225mW per
100dB (Typ)
package) while also saving board space and cost.
o
Low Offset Voltage Drift . . . . . . . . . . . . . . . 3V/ C (Typ)
This impressive combination of features make this amplifier
No Crossover Distortion
ideally suited for designs ranging from audio amplifiers and
active filters to the most demanding signal conditioning and
Standard Quad Pinout
instrumentation circuits.
Applications
Ordering Information
High Q Active Filters
PART TEMPERATURE
Audio Amplifiers
NUMBER RANGE PACKAGE
Integrators
o o
HA1-5104/883 -55 C to +125 C 14 Lead CerDIP
Signal Generators
Instrumentation Amplifiers
Pinout
HA-5104/883
(CERDIP)
TOP VIEW
1 14
OUT 1 OUT 4
2 13 -IN4
-IN1
--
1 4
+
+
3 12
+IN1 +IN4
4 11
V+ V-
5 10
+IN2 +IN3
+
+
3
2
- -
6 9 -IN3
-IN2
7 8
OUT 2
OUT 3
FN3710 Rev 1.00 Page 1 of 5
April 2002HA-5104/883
Absolute Maximum Ratings Thermal Information
Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . . 40V Thermal Resistance
JA JC
o o
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V CerDIP Package . . . . . . . . . . . . . . . . . . . 75 C/W 20 C/W
o o
Voltage at Either Input Terminal . . . . . . . . . . . . . . . . . . . . . . V+ to V- Package Power Dissipation Limit at +75 C for T +175 C
J
Peak Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Indefinite CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.33W
o
(One Amplifier Shorted to Ground) Package Power Dissipation Derating Factor Above +75 C
o o
Junction Temperature (T ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175 C CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3mW/ C
J
o o
Storage Temperature Range . . . . . . . . . . . . . . . . . -65 C to +150 C
ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <2000V
o
Lead Temperature (Soldering 10s). . . . . . . . . . . . . . . . . . . . +300 C
CAUTION: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief
JA
TB379 for details.
Operating Conditions
o o
Operating Temperature Range. . . . . . . . . . . . . . . . -55 C to +125 C V 1/2 (V+ - V-)
INCM
Operating Supply Voltage 5V to15V R 2k
L
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS
Device Tested at: V = 15V, R = 100 , R = 500k, V = 0V, Unless Otherwise Specified.
SUPPLY SOURCE LOAD OUT
LIMITS
GROUP A
PARAMETERS SYMBOL CONDITIONS SUBGROUPS TEMPERATURE MIN MAX UNITS
o
Input Offset Voltage V V = 0V 1 +25C-2.5 2.5 mV
IO CM
o o
2, 3 +125 C, -55C-3.0 3.0 mV
o
Input Bias Current +I V = 0V, 1+25 C -200 200 nA
B CM
+R = 10k ,
S
o o
2, 3 +125 C, -55 C -325 325 nA
-R = 100
S
o
-I V = 0V, 1+25 C -200 200 nA
B CM
+R = 100 ,
S
o o
2, 3 +125 C, -55 C -325 325 nA
-R = 10k
S
o
Input Offset Current I V = 0V, 1+25 C -75 75 nA
IO CM
+R = 10k ,
S
o o
2, 3 +125 C, -55 C -125 125 nA
-R = 10k
S
o
Common Mode Range +CMR V+ = +3V, V- = -27V 1 +25C+12 - V
o o
2, 3 +125 C, -55C+12 - V
o
-CMR V+ = +27V, V- = -3V 1 +25C- -12 V
o o
2, 3 +125 C, -55C- -12 V
o
Large Signal Voltage +A V = 0V and +10V, 4+25 C 100 - kV/V
VOL OUT
Gain R = 2k
L
o o
5, 6 +125 C, -55 C 100 - kV/V
o
-A V = 0V and -10V, 4+25 C 100 - kV/V
VOL OUT
R = 2k
L
o o
5, 6 +125 C, -55 C 100 - kV/V
o
Common Mode +CMRR V = +5V, 1+25C86 - dB
CM
Rejection Ratio V+ = +10V, V- = -20V,
o o
2, 3 +125 C, -55C86 - dB
V = -5V
OUT
o
-CMRR V = -5V, 1+25C86 - dB
CM
V+ = +20V, V- = -10V,
o o
2, 3 +125 C, -55C86 - dB
V = +5V
OUT
FN3710 Rev 1.00 Page 2 of 5
April 2002