DATASHEET X9119 FN8162 Rev 5.00 1024 Tap, Low Power, 2-Wire Interface, Digitally Controlled (XDCP) July 5, 2016 Potentiometer The X9119 integrates a single digitally controlled Features potentiometer (XDCP) on a monolithic CMOS integrated 1024 resistor taps 10-bit resolution circuit. 2-Wire serial interface for write, read, and The digital controlled potentiometer is implemented using transfer operations of the potentiometer 1023 resistive elements in a series array. Between each element are tap points connected to the wiper terminal Wiper resistance, 40 typical at V = 5V CC through switches. The position of the wiper on the array is Four nonvolatile data registers controlled by the user through the 2-wire bus interface. The potentiometer has associated with it a volatile Wiper Counter Nonvolatile storage of multiple wiper positions Register (WCR) and four nonvolatile data registers that can be Power-on recall, loads saved wiper position on power-up. directly written to and read by the user. The contents of the WCR controls the position of the wiper on the resistor array Standby current <3A maximum through the switches. Power-up recalls the contents of the V : 2.7V to 5.5V operation CC default data register (DR0) to the WCR. 100k end-to-end resistance The XDCP can be used as a 3-terminal potentiometer or as a 100 yr. data retention 2-terminal variable resistor in a wide variety of applications including control, parameter adjustments and signal Endurance: 100,000 data changes per bit per register processing. 14 Ld TSSOP Low power CMOS Single supply version of the X9118 Pb-free available (RoHS compliant) V R CC H WRITE ADDRESS POWER-ON RECALL READ 100k DATA TRANSFER 1024-TAPS STATUS BUS WIPER COUNTER 2-WIRE POT REGISTER (WCR) INTERFACE BUS AND WIPER INTERFACE DATA REGISTERS CONTROL (DR0-DR3) CONTROL R V NC NC R W L SS FIGURE 1. FUNCTIONAL DIAGRAM FN8162 Rev 5.00 Page 1 of 18 July 5, 2016X9119 System Level Applications Adjust the contrast in LCD displays Circuit Level Control the power level of LED transmitters in communication Vary the gain of a voltage amplifier systems Provide programmable DC reference voltages for comparators Set and regulate the DC biasing point in an RF power amplifier and detectors in wireless systems Control the volume in audio circuits Control the gain in audio and home entertainment systems Trim out the offset voltage error in a voltage amplifier circuit Provide the variable DC bias for tuners in RF wireless systems Set the output voltage of a voltage regulator Set the operating points in temperature control systems Trim the resistance in Wheatstone bridge circuits Control the operating point for sensors in industrial systems Control the gain, characteristic frequency and Q-factor in filter Trim offset and gain errors in artificial intelligent circuits systems Set the scale factor and zero point in sensor signal conditioning circuits Vary the frequency and duty cycle of timer ICs Vary the DC biasing of a pin diode attenuator in RF circuits Provide a control variable (I, V, or R) in feedback circuits Ordering Information POTENTIOMETER TEMP PART NUMBER V LIMITS ORGANIZATION RANGE PACKAGE CC (Notes 2, 3)PART MARKING (V) (k ) (C) RoHS COMPLIANT PKG. DWG. X9119TV14IZ X9119 TVZI 5 10% 100 -40 to +85 14 Ld TSSOP (4.4mm) M14.173 X9119TV14Z X9119 TVZ 0 to +70 14 Ld TSSOP (4.4mm) M14.173 X9119TV14Z-2.7 X9119 TVZF 2.7 to 5.5 0 to +70 14 Ld TSSOP (4.4mm) M14.173 X9119TV14IZ-2.7 (Note 1) X9119 TVZG -40 to +85 14 Ld TSSOP (4.4mm) M14.173 NOTES: 1. Add T1 suffix for 2.5k unit tape and reel option. 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3. For Moisture Sensitivity Level (MSL), please see product information page for X9119. For more information on MSL, please see tech brief TB363. V CC POWER ON RECALL DR0 DR1 R H SCL WIPER INTERFACE 100k COUNTER SDA AND DATA 1024-TAPS REGISTER A2 CONTROL (WCR) R DR2 DR3 L CIRCUITRY A1 CONTROL A0 R W WP V SS FIGURE 2. DETAILED FUNCTIONAL DIAGRAM FN8162 Rev 5.00 Page 2 of 18 July 5, 2016