ATS01N232LU Schneider

Product data sheet ATS01N232LU Characteristics soft starter for asynchronous motor - ATS01 - 32 A - 200..240V - 7.5 KW Product availability: Stock - Normally stocked in distribution facility Main Range of product Altistart 01 Product or component Soft starter type Product destination Asynchronous motors Product specific applica- Simple machine tion Device short name ATS01 Phase 3 phases Us rated supply volt- 200...240 V - 10...10 % age Motor power kW 7.5 kW 3 phases 200...240 V Motor power hp 10 hp 3 phases 200...240 V IcL starter rating 32 A Utilisation category AC-53B EN/IEC 60947-4-2 Current consumption 160 A at nominal load Type of start Start with voltage ramp Power dissipation in W 324.5 W in transient state 4.5 W at full load and at end of starting Complementary Assembly style With heat sink Function available Integrated bypass Supply voltage limits 180...264 V Supply frequency 50...60 Hz - 5...5 % Network frequency 47.5...63 Hz Output voltage <= power supply voltage Uc control circuit voltage Built into the starter Starting time 1 s 50 10 s 5 5 s 10 Adjustable from 1 to 10 s Deceleration time symb Adjustable from 1 to 10 s Starting torque 30...80 % of starting torque of motor connected directly on the line supply Discrete input type Logic LI1, LI2, BOOST stop, run and boost on start-up functions <= 8 mA 27 kOhm Discrete input voltage 24...40 V Discrete input logic Positive LI1, LI2, BOOST < 5 V and <= 0.2 mA > 13 V >= 0.5 mA Discrete output current 2 A DC-13 3 A AC-15 Discrete output type Open collector logic LO1 end of starting signal Relay outputs R1A, R1C NO Discrete output voltage 24 V 6...30 V open collector logic Minimum switching current 10 mA 6 V DC relay outputs Maximum switching current 2 A 250 V AC inductive cos phi = 0.5 20 ms relay outputs 2 A 30 V DC inductive cos phi = 0.5 20 ms relay outputs Display type 1 LED green starter powered up 1 LED yellow nominal voltage reached Tightening torque 16.81...22.12 lbf.in (1.9...2.5 N.m) 4.42 lbf.in (0.5 N.m) Aug 9, 2019 1 The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein. This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications. It is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof. Neither Schneider Electric Industries SAS nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information contained herein.Electrical connection 4 mm screw clamp terminal rigid 1 1...10 mm AWG 8 power circuit Screw connector rigid 1 0.5...2.5 mm AWG 14 control circuit 4 mm screw clamp terminal rigid 2 1...6 mm AWG 10 power circuit Screw connector rigid 2 0.5...1 mm AWG 17 control circuit Screw connector flexible with cable end 1 0.5...1.5 mm AWG 16 control circuit 4 mm screw clamp terminal flexible without cable end 1 1.5...10 mm AWG 8 power circuit Screw connector flexible without cable end 1 0.5...2.5 mm AWG 14 control cir- cuit 4 mm screw clamp terminal flexible with cable end 2 1...6 mm AWG 10 power circuit 4 mm screw clamp terminal flexible without cable end 2 1.5...6 mm AWG 10 power circuit Screw connector flexible without cable end 2 0.5...1.5 mm AWG 16 control circuit Marking CE Operating position Vertical +/- 10 degree Height 6.06 in (154 mm) Width 1.77 in (45 mm) Depth 5.16 in (131 mm) Product weight 1.23 lb(US) (0.56 kg) Compatibility code ATS01N2 Motor power range AC-3 7...11 kW at 200...240 V 3 phases Motor starter type Soft starter Environment Electromagnetic compatibility Damped oscillating waves level 3 IEC 61000-4-12 Electrostatic discharge level 3 IEC 61000-4-2 Immunity to electrical transients level 4 IEC 61000-4-4 Immunity to radiated radio-electrical interference level 3 IEC 61000-4-3 Voltage/Current impulse level 3 IEC 61000-4-5 Conducted and radiated emissions level B CISPR 11 Conducted and radiated emissions level B IEC 60947-4-2 EMC immunity EN 50082-2 Harmonics IEC 1000-3-2 Harmonics IEC 1000-3-4 Immunity to conducted interference caused by radio-electrical fields level 3 IEC 61000-4-6 Micro-cuts and voltage fluctuation IEC 61000-4-11 EMC immunity EN 50082-1 Standards EN/IEC 60947-4-2 Product certifications CCC C-Tick CSA UL B44.1-96/ASME A17.5 for starter wired to the motor delta terminal GOST IP degree of protection IP20 Pollution degree 2 EN/IEC 60947-4-2 Vibration resistance 1.5 mm peak to peak 3...13 Hz EN/IEC 60068-2-6 1 gn 13...150 Hz EN/IEC 60068-2-6 Shock resistance 15 gn 11 ms EN/IEC 60068-2-27 Relative humidity 5...95 % without condensation or dripping water EN/IEC 60068-2-3 Ambient air temperature for operation 14...104 F (-10...40 C) without derating 104...122 F (40...50 C) with current derating of 2 % per C Ambient air temperature for storage -13...158 F (-25...70 C) EN/IEC 60947-4-2 Operating altitude <= 3280.84 ft (1000 m) without derating > 3280.84 ft (1000 m) with current derating of 2.2 % per additional 100 m Ordering and shipping details Category 22392 - ATSU01/ATS01 LOW HP SOFT STARTERS Discount Schedule I11 GTIN 00785901612551 Nbr. of units in pkg. 1 Package weight(Lbs) 1.4399999999999999 Returnability Y Country of origin DE 2