ACS108-6SN Datasheet 0.8 A - 600 V overvoltage protected AC switch (ACS) Features COM Enables equipment to meet IEC 61000-4-5 surge with overvoltage crowbar technology High noise immunity against static dV/dt and IEC 61000-4-4 burst Needs no external protection snubber or varistor G Reduces component count by up to 80% and Interfaces directly with the micro- COM controller OUT Common package tab connection supports connection of several alternating current switches on the same cooling pad SOT-223 V gives headroom before clamping then crowbar action CL OUT Applications Alternating current on/off static switching in appliances and industrial control systems G Driving low power high inductive or resistive loads like: relay, valve, solenoid, dispenser pump, fan, low power motor, door lock, air flow dumper COM COM Common drive reference to connect lamp to the mains OUT Output to connect to the load. G Gate input to connect to the controller through gate resistor Description The ACS108-6SN belongs to the AC switch range (built with A. S. D. technology). Product status link This high performance switch can control a load of up to 0.8 A. ACS108-6SN These devices switch include an overvoltage crowbar structure to absorb the inductive turn-off energy, and a gate level shifter driver to separate the digital Product summary controller from the main switch. It is triggered with a negative gate current flowing out I 0.8 A of the gate pin. T(RMS) Note: : A.S.D. is a registered trademark of STMicroelectronics V , V 600 V DRM RRM Note: TM: ACS is a trademark of STMicroelectronics I 10 mA GT DS12896 - Rev 1 - February 2019 www.st.com For further information contact your local STMicroelectronics sales office.ACS108-6SN Characteristics 1 Characteristics Table 1. Absolute maximum ratings (T = 25 C, unless otherwise specified) amb Symbol Parameter Value Unit T = 76 C amb I On-state rms current (full sine wave), S = 5cm 0.8 A T(RMS) T = 104 C tab t = 20 ms 13 p Non repetitive surge peak on-state current I A TSM T initial = 25 C, (full cycle sine wave) j t = 16.7 ms 13.7 p 2 2 2 t = 10 ms I t I t for fuse selection 1.1 A s p Critical rate of rise on-state current I = 2 x I , tr 100 ns f = 120 Hz, T = 125 C dI/dt 100 A/s G GT j (1) V Non repetitive line peak pulse voltage 2 kV PP P Average gate power dissipation T = 125 C 0.1 W G(AV) j V Peak positive gate voltage T = 125 C 10 V GM j I Peak gate current (t = 20 s) T = 125 C 1 A GM p j T Storage temperature range -40 to +150 C stg T Operating junction temperature range -30 to +125 C j 1. according to test described by standard IEC 61000-4-5, see Figure 17. Overvoltage ruggedness test circuit for resistive and inductive loads, T = 25 C (conditions equivalent to IEC 61000-4-5 standard) for conditions amb Table 2. Electrical characteristics (T = 25 C, unless otherwise specified) j Symbol Test conditions Quadrant Value Unit (1) I Max. 10 mA GT V = 12 V, R = 33 II - III OUT L V Max. 1.0 V GT V V = V , R = 3.3 k, T = 125 C II - III Min. 0.15 V GD OUT DRM L j I I = 100 mA Max. 10 mA H OUT I I = 1.2 x I Max. 25 mA L G GT V = 402 V, gate open, T = 125 C dV/dt Min. 2000 V/s OUT j (dI/dt)c Without snubber (15 V/s), T = 125 C, turn-off time 20 ms Min. 2 A/ms j V I = 0.1 mA, t = 1 ms Min. 650 V CL CL p 1. Minimum I is guaranteed at 10% of I max. GT GT Table 3. Static electrical characteristics Symbol Test conditions Value Unit (1) I = 1.1 A, t = 500 s T = 25 C V Max. 1.3 V TM TM p j (1) V Threshold voltage T = 125 C Max. 0.85 V j TO (1) T = 125 C R Dynamic resistance Max. 300 m d j I T = 25 C 2 A j DRM V = V / V Max. OUT DRM RRM I T = 125 C 0.2 mA RRM j DS12896 - Rev 1 page 2/14