TLP513 TOSHIBA Photocoupler GaA As IRED LED + Photo IC TLP513 Line Receiver Unit: mm Microprocessor System Interface Data transfers between circuits of different potentials Computer Terminal Interface Ground Loop Elimination TLP513 is a 6-PIN DIP photocoupler, which consists of a GaAAs IRED LED and a high-gain, high-speed IC detector chip. It has a Schottky clamped transistor and has an open collector output type. Threshold input current: I = 5 mA (max) F Switching Speed: 10 MBd Guaranteed performance over temperature: 0 to 70C Isolation voltage: 2500 V (min) rms JEDEC UL recognized: UL1577, File no. E67349 JEITA TOSHIBA 117A8 Truth Table (positive Logic) Weight: 0.4 g (typ.) Input Output H L L H Pin Configuration (top View) 1: Anode 2: Cathode 3: N.C. 4: GND 5: V (open-collector) O 6: V CC Schematic Note: A 0.1 F bypass capacitor must be connected between pins 6 and 4. Start of commercial production 1987-09 1 2017-08-21 TLP513 Absolute Maximum Rating (Ta = 25C) Characteristics Symbol Rating Unit Forward current I 20 mA F Forward current derating (Ta 85C) IF/Ta -1.6 mA/C Pulse forward current (Note 1) I 40 mA FP Peak transient forward current (Note 2) I 1 A FPT Reverse voltage V 5 V R Input power dissipation P 100 mW D Input power dissipation derating(Ta 85C) P /C -2.5 mW/C D Output current I 25 mA O Output voltage V 7 V O Supply voltage (Note 3) V 7 V CC Output power dissipation P 40 mW O Output power dissipation derating (Ta 85C) Po/ Ta -1.0 mW/C Storage temperature range T 55 to 125 C stg Operating temperature range T 40 to 85 C opr Lead solder temperature (10 s) (Note 4) T 260 C sol Isolation voltage BV 2500 V (Note 5) S rms Note: Using continuously under heavy loads (e.g. application of high temperature/current/voltage and a significant change in temperature, etc.) may cause this product to decrease in reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (Handling Precautions/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 1: 50% duty cycle, 1 ms pulse width. Note 2: Pulse width 1 s, 300 pps. Note 3: 1 minute maximum. Note 4: Soldering is performed 2mm from the bottom of the package. Note 5: AC, 1minute, R.H. 60% Device considered a two-terminal device: 1, 2 and 3 shorted together and pins 4, 5 and 6 shorted together. Recommended Operating Conditions Characteristics Symbol Min Typ. Max Unit L level input voltage V 3 0 1.0 V FL H level input current I 6.3* 8 20 mA FH Supply voltage** V 4.5 5 5.5 V CC Fan-out (TTL load) N 8 Operating temperature T 0 70 C opr Note: The recommended operating conditions are given as a design guideline to obtain the expected performance of the device. In addition, each item is an independent guideline. In developing designs using this product, please confirm the specified characteristics shown in this document. * 6.3 mA is a guard banded value which allows for at least 20% CTR degradation. Initial input current threshold is 5 mA or less. ** This item denotes the operating range and not the recommended operating conditions. 2 2017-08-21 Detector LED