LH1522AB, LH1522AAC, LH1522AACTR www.vishay.com Vishay Semiconductors Dual 1 Form A Solid-State Relay (Normally Open) FEATURES Isolation test voltage 5300 V RMS Current limit protection 1 8 S1 Typical R 12 ON Load voltage 200 V 2 7 S1 Load current 200 mA / 140 mA 3 6 S2 Clean bounce free switching Low power consumption 4 5 S2 Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 APPLICATIONS General telecom switching Security equipment DESCRIPTION Instrumentation The LH1522 dual 1 Form A relays are SPST normally open Industrial controls switches that can replace electromechanical relays in many Automatic test equipment applications. They are constructed using a GaAIAs LED for actuation control and MOSFET switches for the output. In addition, the LH1522 SSRs employ current-limiting circuitry AGENCY APPROVALS when overvoltage protection is provided. UL1577, file no. E52744 ORDERING INFORMATION DIP SMD L H 1522 A T R PART NUMBER ELECTR. PACKAGE TAPE AND 7.62 mm > 0.1 mm VARIATION CONFIG. REEL PACKAGE UL SMD-8, tape and reel LH1522AACTR SMD-8, tube LH1522AAC DIP-8, tube LH1522AB Rev. 1.9, 05-Jul-2018 Document Number: 83821 1 For technical questions, contact: optocoupleranswers vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 LH1522AB, LH1522AAC, LH1522AACTR www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (T = 25 C, unless otherwise specified) amb PARAMETER CONDITION SYMBOL VALUE UNIT INPUT IRED continuous forward current I 50 mA F IRED reverse voltage V 5V R Input power dissipation P 80 mW diss OUTPUT DC or peak AC load voltage V 200 V L Continuous DC load current at 25 C, I 200 mA L one channel Continuous DC load current at 25 C, I 140 mA L two channels SSR output power dissipation P 550 mW diss SSR Ambient temperature range T -40 to +85 C amb Storage temperature range T -40 to +150 C stg Soldering temperature t = 10 s max. T 260 C sld Note Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. ELECTRICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT INPUT IRED forward current, switch turn-on I = 100 mA, t = 10 ms I -0.4 2 mA L Fon IRED forward current, switch turn-off V = 200 V I 0.05 0.35 - mA L Foff IRED forward voltage I = 10 mA V 1.15 1.36 1.45 V F F IRED reverse current V = 5 V I - - 10 A R R OUTPUT On-resistance I = 5 mA, I = 50 mA R -12 15 F L ON Off-resistance I = 0 mA, V = 100 V R 0.5 5000 - G F L OFF I = 0 mA, V = 100 V I - < 1 200 nA F L O Off-state leakage current I = 0 mA, V = 200 V I - < 1 1000 nA F L O I = 0 mA, V = 1 V, 1 MHz C -39 - pF F L O Output capacitance pin 3 to 4 I = 0 mA, V = 50 V, 1 MHz C -6 - pF F L O Current limit AC/DC I = 5 mA, t = 5 ms, V = 6 V I 300 440 550 mA F L limit TRANSFER Capacitance (input to output) V = 1 V C -0.4 - pF IO IO Note Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements. SWITCHING CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Turn-on time I = 5 mA, I = 50 mA t -0.20 2 ms F L on Turn-off time I = 5 mA, I = 50 mA t -0.04 2 ms F L off Rev. 1.9, 05-Jul-2018 Document Number: 83821 2 For technical questions, contact: optocoupleranswers vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000
