CRD200DA12E-XM3
200 kW High Performance Three Phase Reference Design with Three CAB400M12XM3
1200 V, 400 A SiC Half Bridge Modules + Three CGD12HBXMP Gate Drivers
Technical Features Package
Optimized for Crees All-SiC, Low Inductance,
Switching-Loss Optimized XM3 Power Module
Complete Stackup, including: Modules, Cooling,
Bussing, Gate Drivers, Voltage / Current Sensors,
and Controller
High-Frequency, Ultra-Fast Switching Operation
with Ultra-Low Loss, Low Parasitic Bussing
System Benefits
Enables Compact, Lightweight Systems
Increased Power Density
High Efficiency Operation
Reduced Thermal Requirements
Reduced System Cost
Applications
High Power Density New Product Development
High Frequency Converter Applications
Vehicle Traction Inverters
Active Front Ends
Uninterruptible Power Supplies
Industrial Motor Drives
Energy Storage
Grid-Tied Distributed Generation: Solar and Wind
Smart-Grid / Flexible AC Transmission Systems
Maximum Ratings (T = 25 C unless otherwise specified)
C
Symbol Parameter Value Unit Test Conditions
V Maximum Drain-Source Voltage 1200
DSmax
DC Bus Voltage, Maximum 900
V
V
DC
DC Bus Voltage, Recommended 800
T = 30 C at 10 kHz
A
I DC Bus Current Ripple, Maximum 300 A
DC
(Set by capacitor rating)
Rev. A, 2020-01-15 CRD200DA12E-XM3 4600 Silicon Dr., Durham, NC 27703
Copyright 2020 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo, Wolfspeed, and the Wolfspeed logo are
1
registered trademarks of Cree, Inc. Other trademarks, product, and company names are the property of their respective owners and do not imply specific product and/or vendor
endorsement, sponsorship or association.Electrical System Ratings (T = 25C unless otherwise specified)
C
Symbol Parameter Min. Typ. Max. Unit Test Conditions
V = 480 V
AC, out rms
WEG coolant, 50% blend, 12 L/
min., f = 10 kHz,
sw
I AC Output Phase Current (RMS) 240 A
(rms)
V = 800 V, f = 300 Hz,
DC out
DPF = 1.0,
T = 25 C, T = 25 C
coolant a
f Switching Frequency 20 80 kHz Based on gate drive power
SW
f Fundamental Output Frequency 550 Hz Controller limited
out
C DC Bus Capacitor Bank Capacity 300 F 10 kHz
DC
L DC Bus Capacitor Bank ESL 3.5 nH
DC
R DC Bus Capacitor Bank ESR 0.4 m 10 kHz
DC
L DC Bus Stray Inductance 1.8 nH
Environmental Ratings
Symbol Parameter Min. Typ. Max. Unit Test Conditions
Higher ambient temperature
T Ambient Temperature 25 40
a
possible with power derating.
Switching frequency and phase
C
T Coolant Temperature 25 90 current must be selected as to
coolant
not exceed T .
J,Max
T Storage Temperature -40 85
stg
Installation Altitude 2000 m Without voltage derating
Thermal & Mechanical Characteristics
Symbol Parameter Min. Typ. Max. Unit Test Conditions
2
A Area 812 cm
W Weight 6.2 kg
V Volume 9.3 L
P Coolant Operating Pressure 5 bar
p Pressure Drop 200 mbar 12 L/min, T = 25C
coolant
11.0 AC & DC Terminals, M10 bolts
Module Power Terminals
2.0 4.0 5.0
Mounting Torque N-m M5 Bolts
Module Baseplate
2.0 3.0 4.0
M4 Bolts
Rev. A, 2020-01-15 CRD200DA12E-XM3 4600 Silicon Dr., Durham, NC 27703
Copyright 2020 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo, Wolfspeed, and the Wolfspeed logo are
2
registered trademarks of Cree, Inc. Other trademarks, product, and company names are the property of their respective owners and do not imply specific product and/or vendor
endorsement, sponsorship or association.