BISTABLE RELAY PBM-01 INSTRUCTION MANUAL Zak ad Mechaniki i Elektroniki ZAMEL sp.j. J.W. Dzida, K. odzi ska ul. Zielona 27, 43-200 Pszczyna, Poland Tel. +48 (32) 210 46 65, Fax +48 (32) 210 80 04 www.zamelcet.com, e-mail: marketing zamel.pl DESCRIPTION TECHNICAL DATA PBM-01 The bistable relay PBM-01 is used to control lighting or other devices by me- Input (supply) terminals: L, N ans of monomodular pushbuttons con- Input rated voltage: 230 V~ nected in a parallel way. Pushing any Input voltage tolerance: -15 +10 % button causes switching on or switching Nominal frequency: 50 / 60 Hz off the devices connected to output termi- Rated power consumption: 24 mA nals. Using this system gives the possibi- Supply voltage control indicator: LED green lity of creating intelligent lighting control Release terminals: IN, IN, IN systems. Release control current: 930 A Power/relay supply indicator: LED red Relay operating indicator: TEST button FEATURES Output relay parameters: 1NO - 16 A / 250 V AC1 4000 VA Number of terminal clamps: 8 Bistable lighting control Input rated in- 2 Section of connecting cables: 0,2 2,50 mm dicator LED green, o Ambient temperature range: -20 +45 C relay mode indicator LED red, Operating position: freely system releasing from the L or N ca- Mounting: rail TH 35 (PN-EN 60715) ble, Protection degree: IP20 (PN-EN 60529) cooperation with monostable push- Protection level: II buttons equipped with illumination lamps, Overvoltage category: II TEST function, Pollution degree: 2 double-wire controll installation, Napi cie udarowe: 1 kV (PN-EN 61000-4-5) voltage relay output - one NO (normal Dimensions: monomodular (17,5 mm) 90x17,5x66 mm closed) contact max 16 A capacity Weight: 78 g monomodular casing TH-35 DIN rail Reference standards: PN-EN 60669-1 PN-EN 60669-2-1 installation. PN-EN 61000-4-2,3,4,5,6,11 The device is designed for APPEARANCE single-phase installation and must be installed in accor- Input supply terminal (L) Input supply terminal (N) dance with standards valid in a particular country. The device should be connected CAUTION Release terminals according to the details inc- luded in this operating manual. Installation, (IN, IN, IN) connection and control should be carried out by a quali ed electrician staff, who act in accordance with the service manual and the device functions. Disassembling of the Supply voltage control indicator device is equal with a loss of guarantee Power/relay supply indicator and can cause electric shock. Before in- stallation make sure the connection cables are not under voltage. The cruciform head Relay test screwdriver 3,5 mm should be used to in- stal the device. Improper transport, storage, and use of the device in uence its wrong functioning. It is not advisable to instal the device in the following cases: if any device part is missing or the device is damaged or deformed. In case of improper functioning of the device contact the producer. The symbol means selective collecting of electrical and electronical equipment. It is forbidden to put Output (load) the used equipment together relay terminals (11, 11, 14) with other waste VER. 001 03.11.2009MOUNTING, FUNCTIONING CONNECTION INNER DIAGRAM 1. Disconnect the power supply from the L N mains by the phase fuse, the circuit- breaker or the switch-disconnector IN that are joined to the proper circuit, IN 2. Check if there is no voltage on con- IN T nection cables by means of a spe- cial measure equipment, 3. Install PBM-01 device in the switch- 11 11 14 board on TH-35 DIN rail, 4. Connect the cables with the terminals according to installing diagram, 5. Switch on the power supply from the TIME COURSE mains, 6. Push the TEST button several times to check the relay operation correct- U t ness. IN t t The device is ready to work after switching on power supply. The relay operation correctness can be checked by pushing the TEST button placed on the front panel. The system should RELAY CAPACITY switch on and off the load connected to its output terminals. Mono modular pu- shbuttons can be connected in a paralell way which enables the lighting control from different places. Lighted pushbut- tons version is possible. DIMENSIONS APPLICATION LOCAL CONTROL CENTRAL RESET BISTABLE RELAYS PRODUCT FAMILY The time relay PBM-01 belongs to PBM time relay product family. Supply version: Typical use: 24V - 24V AC/DC available for PBM-01, PBM-02, PBM-03, The bistable relay operating the stair- 12-24V- 1224V AC/DC available for case lighting (e.g. indoor lighting) are con- PBM-05 U - universal supplying voltage trolled by means of mono modular push- 12230V AC/DC buttons that can be connected in a parallel Device version: 01 - basic way. The buttons can be placed in different places which gives the possibility of creating universal 02 - extended: SET, RESET functions and state storage lighting systems control. The bistable relay cooperates with time relay PCM-04 (with set-ups: 03 - with time limit function 04 - zero current consumption with MODE=F, TIME=3, RANGE=2) and the same gives additional function of the central bistable time limit function 05 - zero current consumption, SET, relay switch off (reset) by momentary power cut. RESET functions and time limit function Signal separator coordination SEM-01: Casing type: M - modular version (TH 35 DIN rail) In the bistable control systems signal separators can be used to divide control signals into P - ush junction box 60 version particular relay groups. Device type WARRANTY CARD There is 24 months guarantee on the product 1. ZMIE ZAMEL SP. J. assures 24 months guarantee for the product. 2. The manufacturers guarantee does not cover any of the following actions: a) mechanical damage during transport, loading / unloading or under other circumstances, b) damage caused by incorrect product mounting or misuse, c) damage caused by unauthorised modi cations made by the PURCHASER or any third parties to the product or any other devices needed for the product functioning, d) damage caused by Act of God or any other incidents independent of the manufacturer. 3. The PURCHASER shall lay any claims in writing to the dealer or ZMIE ZAMEL SP. J. 4. ZMIE ZAMEL SP. J. is liable for processing any claim according to current Polish legislation. 5. ZMIE ZAMEL SP. J. shall process the claim at its own discretion: product repair, replacement or money return. 6. The manufacturers guarantee is valid in the Republic of Poland. 7. The PURCHASERs statutory rights in any applicable legislation whether against the retailer arising from the purchase contract or otherwise are not affected by this warranty. Salesman stamp and signature, date of sale VER. 001 03.11.2009