RADIO GATE CONTROLLER ROB-01/12-24V MANUAL INSTRUCTION ZAMEL Sp. z o.o. ul. Zielona 27, 43-200 Pszczyna, Poland tel. +48 (32) 210 46 65, fax +48 (32) 210 80 04 www.zamelcet.com, e-mail: marketing zamel.pl DESCRiPtioN tECHNiCAL DA t A Radio gate controller ROB-01/12- ROB-01/12-24V 24V is a universal (any gate manufactur- Input (supply) terminals: A1, A2 er) operation controller of garage gates Input rated voltage: 12 24 V ~/ and similar electric drives that enables to control their operation by means of Nominal power consumption: 0,2 W EXTA FREE transmitters. It is possible to Number of operation modes: 1 control few things using one remote con- Number of channels: 1 trol - entry gate, garage gate, room light- Transmission: radio 868,32 MHz ing, etc. The device can be connected to Coding way: unidirectional a suitable wire terminal used as an ex- Coding: addressing transmission ternal antenna. Maximum number of transmitters: 32 Range: up to 250 m in the open area Optic signalling of device operation: LED red diode FEAtuRES Additional antenna terminals: ANT Relay output terminals: 11, 14 cooperation with wireless EXTA FREE Relay parameters: 1NO 2 A / 250 V~ AC3 500 VA (dry contact) system transmitters, Number of terminal clamps: 5 operation control of entry gates, garage 2 Section of connecting cables: up to 2,5 mm gates, and other electric drives, o Ambient temperature range: -10 +55 C universal low-voltage power supply Operating position: free (12-24V ~/ ), Casing mounting: installation cable box 60 mm 1 remote control can be used for differ- Casing protection degree: IP20 (EN 60529) ent drives (entry gate, garage) where Protection level: III ROB-01/12-24V device is mounted, Overvoltage category: II connection possibility of external wired Pollution degree: 2 antenna, wide range of operation (up to 250 m), Surge voltage: 1 kV (EN 61000-4-5) possibility of increasing operation range Dimensions: 47,5 x 47,5 x 20 mm by means of RTN-01 retransmitter. Weight: 0,04 kg Reference standard: EN 60669, EN 60950, EN 6091000 The device is designed for APPEARANCE single-phase installation and must be installed in accord- ance with standards valid in a Antenna terminals (ANT) particular country. The device should be connected accord- CAutioN ing to the details included in Relay output terminals (11, 14) this operating manual. Installation, connection and control should be carried out by a qualified electrician staff, who act in accordance with the service manual and the device functions. Input (supply) terminals (A1, A2) In case of casing dismantling an electric shock may occur, and the guarantee is lost then. Before installation make sure the connection cables are not under voltage. The cruciform head screwdriver 3,5 mm should be used to instal the device. Improper transport, storage, Optic signalling of receivers operation and use of the device influence its wrong func - tioning. It is not advisable to instal the device in Programming push-button the following cases: if any device part is missing or the device is damaged or deformed. In case of improper functioning of the device contact the producer. The ZAMEL company devices The symbol means selective which are characterised collecting of electrical and electronic with this sign can cooperate equipment. with each other. It is forbidden to put the used equipment together with other waste. VER. 003 20.05.2011CoNNECtioN MouNtiNG, FuNCtioNiNG ~/+ 1. Disconnect power supply by the phase fuse, the circuit-breaker or the 12 24 V ~/ switch-disconnector combined to the proper circuit. ~/ 2. Check if there is no voltage on connection cables by means of a special measure equipment. 3. Connect the cables to ROB-01/12-24V device terminals in accordance with the installing diagram. EXISTING 4. Switch on the power supply from the mains. GATE CONTROLLER The ROB-01/12-24V device should be mounted in the connection place of manual gate drive release. The receiver operates in impulse mode - af- ter receiving a signal from a programmed transmitter it short circuits relay output terminals (11-14) for about 0,5 seconds. To improve device operation range it is possi- ble to connect an additional external antenna to ANT terminal. A connecting cable of maximum 2 section 2,5 mm can be the antenna. REMotE CoNtRoLS PRoGRAMMiNG Press PROG push-button of ROB-01 device Press the transmitters push-button Release the transmitters push-button. for a longer time till LED red diode switches on for a longer time. LED red diode switches on LED red diode switches on (signal (constant signal). Next release PROG push-button. (first signal pulsates, next the signal is constant). pulsates) and then switches off - THE TRANSMITTER IS ADDED. An exemplary programming procedure with the use of P-257/2 remote controller. The procedure for the rest of radio EXTA FREE transmitters is analogous. CAUTION: Every transmitter can cooperate with ROB-01 in a different mode, depending on how they were added to the device. One transmitter can be added during one programming cycle. Full memory is signalled with pulsating LED red diode. REMotE CoNtRoL DELEtioN Press PROG push-button of ROB-01 device After 5 seconds LED red diode switches on Release the push-button in ROB-01 for a longer time. (signal pulsates) and then it switches off. - MEMORY IS DELETED. CooPERA tioN AND oPERA tiNG RANGE APPLiCAtioN t ransmitter RoB-01/12-24V t ransmitter RoB-01/12-24V ROB-01/12-24V device can be controlled by RNK-02 200 m RNP-02 180 m means of any transmitter RNK-04 200 m RNL-01 180 m of EXTA FREE system. In this application P-256/8 250 m RTN-01 200 m P-256/8 remote control P-257/4 (2) 200 m RCR-01 180 m was used which can control external lighting RNM-10 250 m RTI-01 180 m (ROP-01), roller blinds RNP-01 180 m RXM-01 250 m and a garage gate CAutioN the given range concerns open area - an ide- (SRP-02). al condition without any natural or artificial obstacles. If there are some obstacles between a transmitter and a re- ceiver, it is advisable to decrease the range according to: wood and plaster: from 5 to 20 %, bricks: from 10 to 40 %, reinforced concrete: from 40 to 80 %, metal: from 90 to 100%, glass: from 10 to 20 % over- and underground medium and high electrical pow- er lines, radio and television transmitters, GSM transmit- ters set close to a device system have also a negative influence on the range. WARRANtY CARD There is 24 months guarantee on the product 1. ZAMEL provides a two-year warranty for its products. 2. The ZAMEL warranty does not cover: a) mechanical defects resulting from transport, loading / unloading or other circumstances b) defects resulting from incorrect installation or operation of ZAMEL products c) defects resulting from any changes made by CUS- TOMERS or third parties, to products sold or equipment necessary for the correct operation of products sold d) defects resulting from force majeure or other aleatory events for which ZAMEL is not liable e) power supply (batteries) to be equipped with a device in the moment of sale (if they appear) 3. All complaints in relation to the warranty must be provided by the CUSTOMER in writing to the retailer after discovering a defect. 4. ZAMEL will review complaints in accordance with existing regulations. 5. The way a complaint is settled, e.g. replacement of the product, repair or refund, is left to the discretion of ZAMEL. 6. Guarantee does not exclude, does not limit, nor does it suspend the rights of the PURCHASER resulting from the discrepancy between the goods and the contract. Salesman stamp and signature, date of sale