RZB-01 WIRELESS CONTROL KIT - LIGHTING CoNNECtioN MouNtiNG MANUAL INSTRUCTION 1. Disconnect power supply by the phase fuse, the circuit-breaker or the switch-disconnector combined to the proper circuit. 2. Check if there is no voltage on connec- tion cables by means of a special measure equipment. ZAMEL Sp. z o.o. 3. Connect the cables with the terminals in ac- cordance with the installing diagram. 4. Install ROP-01 device in installation cable box. ul. Zielona 27, 43-200 Pszczyna, Poland 5. Switch on the power supply from the mains. tel. +48 (32) 210 46 65, fax +48 (32) 210 80 04 www.zamelcet.com, e-mail: marketing zamel.pl DEsCRiPtioN tECHNiCAL DA t A RNK-02 ROP-01 CAPACitY RNK-02 FuNCtioNiNG, MouNtiNG RZB-01 set includes radio receiver ROP-01 used in flush and surface mo- Input (supply) terminals: - L, N By pressing the button, the transmitter sends unting and RNK-02 transmitter, battery Input rated voltage: 3 V (CR2032 battery) 230 V AC 750W 500W a signal with 868,32 MHz frequency which con- powered, can be mounted in any place. Battery life: 3 5 years - trols EXTA FREE receivers. Device program- The set gives comfortable solution used Input voltage tolerance: - -15 +10 % ming procedure (adding a transmitter to to control lighting and other receivers re- 250W 375W a receivers memory) is described in par- Nominal frequency: - 50 / 60 Hz motely. ticular EXtA FREE manual instructions. Nominal power consumption: - 0,29 W The device range (up to 250 m depending on Number of operation modes: - 5 APPLiCAtioN a receiver) can be increased by means of a re- Number of channels: 2 1 transmitter or few RTN-01 retransmitters. The device can be mounted in any place by means Transmission: radio 868,32 MHz FEAtuREs of double-sided adhesive tape or wall plugs Coding way: unidirectional 5 x (3 x 30) mm. Coding: addressing transmission complete set of wireless control Maximum number of transmitters: - 32 Mounting by means of wall plugs: (2channel button radio transmitter 1. Remove the button - to do it press the but- Range: up to 250 m in the open area up to 230 m in the open area RNK-02 and 1-channel bistable radio ton on one side, and on the other side put receiver ROP-01), Time adjustment: - 1 s 18 hours (every 1 sec.) a screwdriver into a slot and lift up the button. light operation control and other re- Optic signalling of transmitters operation: LED red diode 2. Find a place on the wall to mount the transmit- ceivers control, Relay output clamps: - 12, 11, 14 ter, make two holes corresponding mounting receivers are easily installed in an holes from the transmitters base. Relay contacts parameters: - 1NO/NC 5A / 250V~ AC1 1250 VA electric-light fitting or in 60 mm junc- 3. Set wall plugs in the holes. Number of terminal clamps: - 5 tion box, 4. Fix the base by means of screwing screws 2 five operation modes: switching on Section of connecting cables: - do 2,5 mm into wall plugs. mode, switching off, monostable, bi- o Ambient temperature range: -10 +55 C 5. Place the button again. stable, time (switch off delay), Operating position: free wide range of operation (up to 180 m), BAttERY CHANGE Casing mounting: wall plugs, double-sided adhesive tape installation cable box 60 mm operation is optically signalled, Battery discharge status is signalled by sev- Casing protection degree: IP20 (EN 60529) low current consumption, possibility of eral LED red diode flashes during transmis- constant work, Protection level: III II sion time. possibility of widening operation range Overvoltage category: - II 1. Remove the button (as in point 1 of mounting). by means of RTN-01 retransmitter. 2. By means of a screwdriver lever up the Pollution degree: 2 printed-circuit board releasing the bottom latch Surge voltage: - 1 kV (EN 61000-4-5) (Fig. 2), and remove it from the base. Dimensions: 90 x 80 x 11,5 mm 47,5 x 47,5 x 20 mm 3. Remove the battery from the latch. Weight: 0,038 kg 0,043 kg 4. Mount a new battery. Watch battery polari- sation marked on the latch. Wrong battery ETSI EN 300 220-1 EN 60669, EN 60950 Reference standard: The device is designed for ETSI EN 300 220-2 EN 61000 mounting may cause device damage. single-phase installation and 5. Put the removed printed-circuit board back in must be installed in accord- 1-channel radio flush receiver ROP-01 the base. ance with standards valid in a operates as a receiver of 8-channel APPEARANCE 6. Put back the button. particular country. The device remote controller P-256/8 and of should be connected accord- 2-channel button radio transmitter CAutioN ing to the details included in CAutioN: While changing the battery, Relay output terminals RNK-02 (light sources switch on/switch this operating manual. Installation, connection it is suggested to press any of the buttons (12, 11, 14) off control). The above mentioned and control should be carried out by a qualified for about 5 seconds before putting it into The ZAMEL company transmitters can also control operation electrician staff, who act in accordance with the a latch. Next press transmission button sev- devices which are of radio lighting switch RWL-01 service manual and the device functions. Input (supply) terminals (L, N) eral times to check its operation. if the trans- characterised with this sign In case of casing dismantling an electric shock and remote control socket RWG-01. can cooperate mitter does not work properly repeat the bat- may occur, and the guarantee is lost then. Be- with each other. tery change procedure. fore installation make sure the connection ca- bles are not under voltage. The cruciform head Optic signalling of receivers operation screwdriver 3,5 mm should be used to instal the WARRANtY CARD Programming buttons device. Improper transport, storage, and use of the device influence its wrong functioning. It Optic signalling of transmitters operation There is 24 months guarantee on the product is not advisable to instal the device in the fol- 1. ZAMEL provides a two-year warranty for its products. lowing cases: if any device part is missing or 2. The ZAMEL warranty does not cover: a) mechanical defects resulting from transport, loading / unloading or other circumstances the device is damaged or deformed. In case of b) defects resulting from incorrect installation or operation of ZAMEL products c) defects resulting from any changes made by CUS- Push-button improper functioning of the device contact the TOMERS or third parties, to products sold or equipment necessary for the correct operation of products sold d) defects resulting producer. from force majeure or other aleatory events for which ZAMEL is not liable e) power supply (batteries) to be equipped with a device in the moment of sale (if they appear) 3. All complaints in relation to the warranty must be provided by the CUSTOMER in writing to the retailer after discovering a defect. The symbol means selective collecting 4. ZAMEL will review complaints in accordance with existing regulations. of electrical and electronic equipment. 5. The way a complaint is settled, e.g. replacement of the product, repair or refund, is left to the discretion of ZAMEL. 6. Guarantee does not exclude, does not limit, nor does it suspend the rights of the PURCHASER resulting from the discrepancy It is forbidden to put the used between the goods and the contract. equipment together with other waste. salesman stamp and signature, date of sale VER. 003 20.05.2011RoP-01 oPERA tioN tiME PRoGRAMMiNG ROP-01 can operate in five modes: 1s 2s ns MoNost ABLE Bist ABLE sWitCH oN tiME the relay operates only (one push-button) the the device switches on the device switches while pressing transmit- device changes relay after pressing the push- off according to the ters push-button. status cyclically always -button. adjusted time (tp), after pressing the same push- sWitCH oFF but it may be switched off before -button. the device switches off adjusted time finishes. Default Press PROG push-button of ROP-01 device for a longer time till Press PROG push-button of ROP-01 device After the adjusted time is after pressing the push- settings - 15 seconds. LED red diode switches on (constant signal). Next release PROG and then release it. LED red diode switches finished (the number of LED -button. push-button. Wait (for about 5 seconds) till LED red diode switches off and then switches on (signal pulsates). red diode flashes) press CAutioN Adjusted time can- on (first signal pulsates, next the signal is constant). Every LED diode pulse equals 1 second. PROG push-button and then not be deleted. release it - TIME IS ADDED. Maximum time is 18 hours. RADio tRANsMittERs DELEtioN RADio tRANsMittERs PRoGRAMMiNG Press PROG push-button of ROP-01 After 5 seconds LED red diode switches on Release the push-button in ROP-01 - device for a longer time. (signal pulsates) and then it switches off. MEMORY IS DELETED. MoNost ABLE mode: CooPERA tioN AND oPERA tiNG RANGE symbol RoP-01 RoP-02 RoB-01 sRP-02 sRP-03 RWG-01 RWL-01 RoM-01 RoM-10 RDP-01 RtN-01 RNK-02 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m Press transmitters Press PROG push-button of ROP-01 device Release transmitters RNK-04 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m Press the same transmitters push- push-button for a for a longer time until LED red diode switches on push-button. LED red diode -button and release it. LED red dio- P-256/8 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m longer time. (constant signal). Next release PROG push-button. switches on de switches on (the signal pulsates) P-257/4 (2) 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m (first signal pulsates, next and next it switches off - RNM-10 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m the signal is constant). THE TRANSMITTER IS ADDED. Bist ABLE mode: RNP-01 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m RNP-02 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m RNL-01 160 m 180 m 180 m lack* lack* 200 m 160 m 200 m 200 m 160 m 200 m RtN-01 200 m 200 m 200 m 200 m 200 m 250 m 200 m 250 m 250 m 200 m 250 m RCR-01 160 m 180 m 180 m lack* lack* 200 m 160 m 200 m 200 m 160 m 200 m Rti-01 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m RXM-01 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m Press PROG push-button of ROP-01 device Press the transmitters push-button Release transmitters push-button. LED red * - 1-channel transmitters do not cooperate with roller blind controllers. for a longer time until LED red diode for a longer time. LED red diode switches diode switches on (the signal pulsates), next CAUTION: The given range concerns open area - an ideal condition without any natural or artificial obstacles. If there are some obstacles be - switches on (constant signal). on (first signal pulsates, the LED red diode switches off - it means tween a transmitter and a receiver, it is advisable to decrease the range according to: Next release PROG push-button. next the signal is constant). the TRANSMITTER IS ADDED. wood and plaster: from 5 to 20 %, bricks: from 10 to 40 %, reinforced concrete: from 40 to 80 %, metal: from 90 to 100%, glass: from 10 to 20 %, over- and underground medium and high electrical power lines, radio and television transmitters, GsM transmitters set close to a device sys - tem have also a negative influence on the range. sWitCH oN/sWitCH oFF mode (two push-buttons): tRANsMittERs RECEiVERs RNK-02 RNL-01 RoP-01 RWL-01 2channel button Radio 1-channel Radio lighting radio transmitter foot transmitter radio receiver switch RNK-04 Rti-01 RoP-02 RWG-01 4-channel button IR/EXTA FREE 2-channel Remote control Press PROG push-button of ROP-01 Press the transmitters push-button Release transmitters push-button. LED radio transmitter transceiver radio receiver socket device for a longer time until LED red for a longer time. LED red diode switches red diode switches on (the signal pulsates), diode switches on (constant signal). on (first signal pulsates, next the LED red diode switches off - it P-256/8 RNM-10 RDP-01 sRP-02 Next release PROG push-button. next the signal is constant). means the TRANSMITTER IS ADDED. 8-channel 4-channel radio 1-channel Radio roller blinds remote controller modular transmitter radio dimmer controller tiME mode (one push-button): P-257/4 RNP-01 RoB-01/12-24V sRP-03 4-channel 4-channel Radio Central radio roller remote controller radio transmitter gate controller blinds controller P-257/2 RNP-02 RoM-01 RoM-10 2-channel 4-channel 1-channel radio 2-channel remote controller radio transmitter modular receiver radio modular receiver Press PROG push-button of ROP-01 Press PROG push-button of ROP-01 Press and release the same transmitters RCR-01 RXM-01 device for a longer time till LED red device and then release it. LED red diode push-button. LED red diode switches on Radio Translator diode switches on (constant signal). switches on (first signal pulsates, (signal pulsates) and then switches off - motion sensor RS-485/EXTA FREE Next release PROG push-button. next the signal is constant). THE TRANSMITTER IS ADDED. ACCEssoRiEs An exemplary programming procedure with the use of P-257/2 remote controller. The procedure for the rest of radio EXTA FREE transmitters is analogous. CAutioN: Every transmitter can cooperate with RoP-01 in a different mode, depending on how they were added to ANt -01 RtN-01 the device. one transmitter can be added during one programming cycle. Full memory is signalled with pulsating LED red diode. External antenna Retransmitter VER. 003 20.05.2011