Technical Information ModSTACK 2LS20017E42W36702 Preliminary data General information IGBT Stack for typical voltages of up to 690 V RMS Rated output current 1520 A RMS High power converter Wind power Motor drives TM PrimePACK 3 module Extended operational temperature Low Vcesat 1 Topology /2B2I Application Inverter Load type Resistive, inductive Semiconductor (Inverter 2x FF1000R17IE4 Section) Heatsink Water cooled Implemented sensors Current, temperature Driver signals IGBT Electrical Design standards EN 50178 Sales - name 2LS20017E42W36702 SP - No. SP000934308 Inverter Section ~ Signal Driver conditioning 1 phase & monitor Electrical interface prepared by: OW date of publication: 2013-10-08 approved by: AR revision: 2.2 1Technical Information ModSTACK 2LS20017E42W36702 Preliminary data Absolute maximum rated values Collector-emitter voltage IGBT T = 25C V 1700 V vj CES Repetitive peak reverse voltage Diode T = 25C V 1700 V vj RRM DC link voltage V 1250 V DC Insulation management according to installation height of 2000 m V 690 V line RMS Insulation test voltage V 2.5 kV ISOL RMS Repetitive peak collector t = 1 ms I 2500 A p CRM2 current inverter section (IGBT) Repetitive peak forward current tp = 1 ms IFRM2 2500 A inverter section (Diode) Continuous current inverter I 1660 A AC2 RMS section Junction temperature under switching conditions Tvjop 150 C Switching frequency inverter fsw2 4 kHz section Notes Further maximum ratings are specified in the following dedicated sections Characteristic values Inverter Section min. typ. max. V = 1100 V, V = 690 V , cos() = 0.85, DC AC RMS Rated continuous current IAC 1520 ARMS f = 50 Hz, f = 2000 Hz, T = 40C, T 150 C AC sine sw inlet j Continuous current at low V = 1100 V, V = 690 V , f = 0 Hz, DC AC RMS AC sine I 770 A AC low RMS frequency f = 2000 Hz, T = 40 C, T 150 C sw inlet j Rated continuous current for IAC 150% = 1660 ARMS, ton over = 3 s, Tj 150 C IAC over1 1110 ARMS 150% overload capability Over current shutdown within 15 s IAC OC 4200 Apeak IAC = 1520 A, VDC = 1100 V, VAC = 690 VRMS, Power losses cos() = 0.85, f = 50 Hz, f = 2000 Hz, P 6700 W AC sine sw loss Tinlet = 40 C, Tj 150 C Controller interface Driver and interface board ref. to separate Application Note DR240 min. typ. max. Auxiliary voltage V 18 24 30 V aux Auxiliary power requirement V = 24 V P 40 W aux aux resistor to GND 1.8 k, capacitor to GND 4 nF, V 0 4 V in low Digital input level logic high = on, min. 15 mA V 11 15 V in high Digital output level open collector, logic low = no fault, max. 15 mA V 0 1.5 V out low V 15 V out high VIU ana2 Analog current sensor output load max 1 mA, 1520 A V 3.3 3.4 3.5 V RMS IV ana2 inverter section V IW ana2 Analog temperature sensor load max 1 mA, TNTC = 66 C, V 6.4 6.5 6.6 V Theta NTC2 output inverter section (NTC) corresponds to T = 150 C at rated conditions j Over temperature shutdown load max 1 mA, TNTC = 75 C VError OT2 8.6 V inverter section prepared by: OW date of publication: 2013-10-08 approved by: AR revision: 2.2 2