CY7C1250KV18-400BZXC Infineon

CY7C1248KV18/CY7C1250KV18 36-Mbit DDR II+ SRAM Two-Word Burst Architecture (2.0 Cycle Read Latency) 36-Mbit DDR II+ SRAM Two-Word Burst Architecture (2.0 Cycle Read Latency) Features Configurations 36-Mbit density (2M 18, 1M 36) With Read Cycle Latency of 2.0 Cycles: CY7C1248KV18 2M 18 450 MHz clock for high bandwidth CY7C1250KV18 1M 36 Two-word burst for reducing address bus frequency Double data rate (DDR) interfaces (data transferred at Functional Description 900 MHz) at 450 MHz The CY7C1248KV18, and CY7C1250KV18 are 1.8 V Available in 2.0 clock cycle latency synchronous pipelined SRAMs equipped with DDR II+ architecture. The DDR II+ consists of an SRAM core with Two input clocks (K and K) for precise DDR timing advanced synchronous peripheral circuitry. Addresses for read SRAM uses rising edges only and write are latched on alternate rising edges of the input (K) Echo clocks (CQ and CQ) simplify data capture in high speed clock. Write data is registered on the rising edges of both K and systems K. Read data is driven on the rising edges of K and K. Each address location is associated with two 18-bit words Data valid pin (QVLD) to indicate valid data on the output (CY7C1248KV18), or 36-bit words (CY7C1250KV18) that burst sequentially into or out of the device. Synchronous internally self-timed writes Asynchronous inputs include an output impedance matching DDR II+ operates with 2.0 cycle read latency when DOFF is input (ZQ). Synchronous data outputs (Q, sharing the same asserted HIGH physical pins as the data inputs D) are tightly matched to the two Operates similar to DDR I device with 1 cycle read latency when output echo clocks CQ/CQ, eliminating the need for separately DOFF is asserted LOW capturing data from each individual DDR SRAM in the system design. 1 Core V = 1.8 V 0.1 V I/O V = 1.4 V to V DD DDQ DD All synchronous inputs pass through input registers controlled by Supports both 1.5 V and 1.8 V I/O supply the K or K input clocks. All data outputs pass through output HSTL inputs and variable drive HSTL output buffers registers controlled by the K or K input clocks. Writes are conducted with on-chip synchronous self-timed write circuitry. Available in 165-ball FBGA package (13 15 1.4 mm) For a complete list of related documentation, click here. Offered in both Pb-free and non Pb-free packages JTAG 1149.1 compatible test access port Phase-locked loop (PLL) for accurate data placement Selection Guide Description 450 MHz 400 MHz Unit Maximum operating frequency 450 400 MHz Maximum operating current 18 600 550 mA 36 760 690 Note 1. The Cypress QDR II+ devices surpass the QDR consortium specification and can support V = 1.4 V to V . DDQ DD Cypress Semiconductor Corporation 198 Champion Court San Jose, CA 95134-1709 408-943-2600 Document Number: 001-57834 Rev. *J Revised January 3, 20181M x 18 Array 512K x 36 Array 1M x 18 Array 512K x 36 Array CY7C1248KV18/CY7C1250KV18 Logic Block Diagram CY7C1248KV18 Write Write 20 A Reg Reg (19:0) Address Register 18 LD K Output CLK R/W Logic K Gen. Control DOFF Read Data Reg. 36 CQ V 18 REF 18 Reg. Reg. CQ Control R/W Logic 18 18 BWS 1:0 Reg. 18 DQ 17:0 QVLD Logic Block Diagram CY7C1250KV18 Write Write 19 A Reg Reg (18:0) Address Register 36 LD K Output CLK R/W Logic K Gen. Control DOFF Read Data Reg. 72 CQ V 36 REF 36 Reg. Reg. CQ Control R/W Logic 36 36 BWS 3:0 Reg. 36 DQ 35:0 QVLD Document Number: 001-57834 Rev. *J Page 2 of 29 Write Add. Decode Write Add. Decode Read Add. Decode Read Add. Decode