TQC0015 High Isolation, Absorptive SPDT Switch Applications Cellular Infrastructure Test and Measurement Smart Energy UHF/VHF LMR General Purpose Broadband Wireless Enable Pin Functionality 16-pin 4x4mm QFN Package Product Features Functional Block Diagram Low Insertion Loss Pin 1 Reference Mark +56dBm Input IP3 NC NC NC NC High Isolation 16 15 14 13 Absorptive V RF2 1 12 DD +1.8V logic compatible Controller V GND 2 11 CTRL Termination off state functionality for output ports Single Positive Voltage Control RFC 3 10 GND 4x4mm 16-pin QFN package NC 4 9 RF1 5 6 7 8 V NC NC NC EN Backside Paddle - RF/DC GND General Description Pin Configuration The TQC0015 is a GaAs FET single-pole, double throw Pin No. Symbol (SPDT) high isolation absorptive switch that provides 1 V DD 1006000 MHz broadband performance. The 2 VCTRL TQC0015 may be operated using a DC supply ranging 3 RFC from +3 to +5 Volts and with control signals compliant to 4 , 68 , 1316 NC +1.8 CMOS logic. The switch has an added functionality 5 V EN with a Disable pin where both output ports are terminated in 50 ohms. 9 RF1 10 , 11 GND The TQC0015 is packaged in a RoHS-compliant, 12 RF2 compact 4x4 mm surface-mount leadless package. Backside Paddle RF/DC GND This SPDT switch is targeted for use in wireless infrastructure, test and measurement, or can be used for Ordering Information any general purpose wireless application. Part No. Description TQC0015 SPDT Absorptive Switch TQC0015-PCB 1004500 MHz Evaluation Board Standard T/R size = 2500 pieces on a 13 reel Data Sheet Rev. H 09-17-14 - 1 of 7 - Disclaimer: Subject to change without notice 2014 TriQuint www.triquint.com TQC0015 High Isolation, Absorptive SPDT Switch Absolute Maximum Ratings Recommended Operating Conditions Parameter Rating Parameter Min Typ Max Units Storage Temperature 65 to +165C V +3.0 +3.3 +5.5 V DD RF Input Power, CW, 50, T = 25C +33dBm VCTRL +1.8 VDD V Supply Voltage (V ) +6V Operating Temp. Range 40 +85 C DD Control Voltage (VCTRL) VDD+0.5V Electrical specifications are measured at specified test conditions. Specifications are not guaranteed over all Operation of this device outside the parameter ranges recommended operating conditions. given above may cause permanent damage. Electrical Specifications Test conditions unless otherwise noted: V =+3.3V, V =+1.8V, Temp.=+25C, 50 system DD CTRL Parameter Conditions Min Typ Max Units Operational Frequency Range 100 6000 MHz Low 0 +0.5 V Control Voltage High +1.2 V V DD 0.11.0 GHz 0.5 0.8 Insertion Loss 1.02.6 GHz 0.7 1.0 dB 2.63.0 GHz 0.8 3.04.5 GHz 0.9 0.11.0 GHz 45 52 1.02.6 GHz 38 43 Isolation RFC to RF1/RF2 dB 2.63.0 GHz 42 3.04.5 GHz 40 0.11.0 GHz 45 50 1.02.6 GHz 35 42 Isolation RF1 to RF2 dB 2.63.0 GHz 41 3.04.5 GHz 38 0.11.0 GHz 20 Return Loss RFC Port 1.02.6 GHz 13 17 dB 2.64.5 GHz 15 Input P1dB f = 2 GHz +34 dBm Input IP3 f = 2 GHz, Pin/tone=+15 dbm, f=1 MHz +56 dBm tON (50% CTL to 90% RF) 240 nS Switching Speed t (50% CTL to 10% RF) 100 nS OFF Total Supply current (I ) 170 250 uA DD Digital Control Voltages Switch Control Truth Table State Bias Condition Signal Path State Low +0.45 V VEN VCTRL RFC to RF1 RFC to RF2 High +1.4 V Low Low Off (Isolation) On (Insertion Loss) Low High On (Insertion Loss) Off (Isolation) High Low Off (Terminated) Off (Terminated) High High Off (Terminated) Off (Terminated) Data Sheet Rev. H 09-17-14 - 2 of 7 - Disclaimer: Subject to change without notice 2014 TriQuint www.triquint.com