A compact 12W constant current switching power module suitable for driving up to ten high power LEDs (Vf = 3.6V). The output current is fixed at 350mA, 500mA or 700mA. Active power factor correction is standard and the converters are UL8750 certified for use with LED assemblies. The driver module features both screw terminal and socket output connections. The socket connector avoids the possibility of miswiring and damaging the LED load if the LEDs are pre-assembled into a wiring harness or lamp fitting. 12W Class II AC/DC LED Power Supply LIGHTLINE Features ENEC, UL, RCM and CB Certified AC/DC-Converter Active Power Factor Corrected >0.95 LED Fused Input, Protected Output with 5 year Warranty 3kVAC Input/Output Isolation DRIVER Output Socket Connector cUL/UL-8750 Certified Low Cost Long 5 Year Warranty Description 12 Watt PFC Single Output Selection Guide Part Nominal Input Current OutputOutput Max Number Input Voltage at 230VAC Voltage Range Current (VAC) (mA) (VDC) (mA) LEDs RACD12-350 universal 200 3-36 350 10 x 1W RACD12-500 universal 200 3-24 500 6 x 2W RACD12-700 universal 200 3-17 700 4 x 2W, 8 x 1W Specifications (typical at 25C and after warm up time unless otherwise specified ) RoHS Input Voltage Range 90-264VAC 2011/65/EU 6/6 Rated Power 12 Watts max. E340696 Input Frequency Range 47-63 Hz UL-8750 Certified Power Factor Full Load, 115VAC/230VAC 0.95 cUL-8750 Certified THD Full Load, 115VAC 7% max. ENEC 61347 Certified Full Load, 230VAC 14% max. Open Circuit Voltage 350mA Version 42VDC (Zener Clamp) 500mA Version 28VDC 700mA Version 24VDC RACD12 Inrush Current (<2mS) 115VAC/230VAC 10A max. Input Current 230VAC, Full Load 200mA max. Leakage Current 115VAC/240VAC - 60/50Hz 0.5mA typ. Input Fuse Standard T1A Output Current Accuracy (combined Tolerance, Load Regulation and Line Regulation) 10%. Minimum Load Open Circuit Protected 1 LED Hold Up Time 18ms min. Operating Frequency 50-120kHz typ. Efficiency at Full Load 78% RMS Isolation Voltage (input to output) 3kVAC / 1 minute Temperature Coefficient 0.02%/C typ. Overload Protection 120% typ. Short Circuit Protection Continuous Current Limit Output Overvoltage Protection Zener Diode Clamp Overtemperature Protection Shutdown, Automatic restart after cooling down Operating Temperature Range Ambient Temperature -20C to +50C (free air convection, according to CE/UL) Case Temperature 81C max. Operating Temperature Range Ambient Temperature -20C to +50C (free air convection, according to ENEC) Case Temperature 85C max. Storage Temperature Range -40C to +100C Weight 100g Packing Quantity 1pc Humidity 95% RH max. Refer to Application Notes continued on next page www.recom-power.com REV: 1/2015 L-25RACD12 LIGHTLINE AC/DC-Converter Series (typical at 25C and after warm up time unless otherwise specified ) Specifications IP Rating IP20, Indoor Use Only PCB Material Plastic Resin with Fibreglass (UL94V-0) Case Material Plastic Designed to meet Standards Electrical Lighting, EMC Emissions EN55015:2006 + A1: 2007 + A2:2009 Limits for Harmonics Emissions EN 61000-3-2:2006 EMC Compatability: Flicker and Voltage Variations EN 61000-3-3:2006 Electrical Lighting: EMC Immunity EN 61547:1995 + A1:2000 Class II Power Supply Safety complies with UL1310 FCC complies with FCC18A THD <20% Certifications LED Lighting Safety UL8750 LED Lighting Safety (Canada) cUL8750 RCM (U21381) AS/NZS 61347.1:2002, IEC 61347-2-13 ENEC Certification, General Safety EN 61347-1: 2008 ENEC Certification, Safety of AC supplied Control Gear for LED Modules EN 61347-2-13: 2006 PSE J61347-1(H20), J61347-2-13(H21), J55015(H20) Design Lifetime 25C ambient >70 x 10 hours in operation Connections AC Input Screw terminal LED Output Screw Terminal LED Output 5.5mm Socket with 2mm Pin (Suitable matching plug Switchcraft S760 or similar)* Note: All LED Drivers may not be used without a load. They must be switched on the primary side only. Noncompliance may damage the LED or reduce its lifetime. Characteristic Maximum Number of LED drivers per circuit breakers Condition Circuit Breaker Circuit Breaker Current Typ 10A 16A 20A 25A 115VAC, 1Ohm C 101 128 171 228 90 phase angle B 61 100 121 150 230VAC, 1Ohm 90 phase angle C 121 164 221 291 B 70 115 139 172 277VAC, 1Ohm 90 phase angle C 139 188 254 334 Package Style and Pinning / Connections * CN1 Function +%+ (> & % L VAC in (L) N VAC in (N) + ( ,+ *3 CN2 Function 5 : + LED+ - LED- *%+ % 5.5mm Socket* Function / Pin LED+ 2 Mounting screws are included Shell LED- . + Tolerenace Tc= Case Temperature Measuring Point XX = +/-0.5mm XX.X =+/-0.25mm The product information and specifications are subject to change without prior notice. RECOM products are not authorized for use in safety-critical applications (such as life support) without RECOMs explicit written consent. A safety-critical application is defined as an application where a failure of a RECOM product may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The buyer shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications. L-26 REV: 1/2015 www.recom-power.com RACD12