VBUS054CD-FHI www.vishay.com Vishay Semiconductors 4-Line BUS-Port ESD-Protection - Flow Through Design FEATURES Compact LLP2513-11L package nc. nc. GND nc. nc. 8 10 9 76 Low package height < 0.6 mm 4-line ESD-protection 11 Low leakage current I < 0.1 A R 123 45 Low load capacitance C = 0.8 pF 21326 D D1 + D1 - GND D2 + D2 - Ideal for high speed data line like 21324 - HDMI, DisplayPort, eSATA - USB, 1394/firewire ESD-protection acc. IEC 61000-4-2 15 kV contact discharge MARKING (example only) 15 kV air discharge Soldering can be checked by standard vision inspection. YYXX No X-ray necessary 20720 e4 - precious metal (e.g. Ag, Au, NiPd, NiPdAu) (no Sn) Dot = pin 1 marking Material categorization: for definitions of compliance YY = type code (see table below) please see www.vishay.com/doc 99912 XX = date code ORDERING INFORMATION TAPED UNITS PER REEL DEVICE NAME ORDERING CODE MINIMUM ORDER QUANTITY (8 mm TAPE ON 7 REEL) VBUS054CD-FHI VBUS054CD-FHI-GS08 3000 15 000 PACKAGE DATA PACKAGE TYPE MOLDING COMPOUND MOISTURE SOLDERING DEVICE NAME WEIGHT NAME CODE FLAMMABILITY RATING SENSITIVITY LEVEL CONDITIONS MSL level 1 VBUS054CD-FHI LLP2513-11L 9X 5.5 mg UL 94 V-0 260 C/10 s at terminals (according J-STD-020) ABSOLUTE MAXIMUM RATINGS VBUS054CD-FHI PARAMETER TEST CONDITIONS SYMBOL VALUE UNIT Peak pulse current Acc. IEC 61000-4-5 t = 8/20 s single shot I 3.5 A P PPM Peak pulse power Acc. IEC 61000-4-5 t = 8/20 s single shot P 45 W P PP Contact discharge acc. IEC 61000-4-2 10 pulses V 15 kV ESD ESD immunity Air discharge acc. IEC 61000-4-2 10 pulses V 15 kV ESD Operating temperature Junction temperature T -40 to +125 C J Storage temperature T -55 to +150 C STG Rev. 1.5, 15-Jul-15 Document Number: 81882 1 For technical questions, contact: ESDprotection vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000VBUS054CD-FHI www.vishay.com Vishay Semiconductors ELECTRICAL CHARACTERISTICS VBUS054CD-FHI (pin 1, 2, 4 or 5 to pin 3) PARAMETER TEST CONDITIONS/REMARKS SYMBOL MIN. TYP. MAX. UNIT Protection paths Number of lines which can be protected N - - 4 lines channel Reverse stand-off voltage Max. reverse working voltage V -- 5 V RWM Reverse voltage at I = 0.1 A V 5- - V R R Reverse current at V = 5 V I - < 0.01 0.1 A RWM R Reverse breakdown voltage at I = 1 mA V 6.9 7.9 8.7 V R BR at I = 1 A V -9.1 11 V PP C Reverse clamping voltage at I = I = 3.5 A V - 11.6 13 V PP PPM C at I = 1 A V -1.6 2.4 V PP F Forward clamping voltage at I = 3.5 A V -3.5 5 V PP F Capacitance at V = 0 V f = 1 MHz C -0.8 1 pF R D Note T = 25 C, unless otherwise specified amb APPLICATION NOTE The VBUS054CD-FHI is a four-line ESD-protection device with the characteristic of a Z-diode with a high ESD-immunity and a very low capacitance which makes it usable for high frequency applications like USB2.0 or HDMI. With the VBUS054CD-FHI four high speed data lines can be protected against transient voltage signals like ESD (Electro Static Discharge). Connected to the data line (pin 1, 2 and pin 4, 5) and to ground (pin 3, 8 and 11) negative transients will be clamped close below the ground level while positive transients will be clamped close above the 5 V working range. The clamping behaviour of the VBUS054CD-FHI is bidirectional but asymmetrical (BiAs) and so it offers the best protection for applications running up to 5 V. Pin configuration: Pin 3, 8 and 11 are internally shorted and have to be connected to ground Pin 1, 2 and 4, 5 are the inputs for the data lines D and D and D and D 1+ 1- 2+ 2- Pin 6, 7 and 9, 10 are not connected internally USB/HDMI Interface nc. nc. GND nc. nc. D1 + D1 - D2 + D2 - 10 9 8 76 11 10 9 8 7 6 123 45 21326 D1 + D1 - GND D2 + D2 - 11 123 4 5 D1 + D1 - GND D2 + D2 - I/O Port Connector 21328 FLOW THROUGH DESIGN Modern digital transmission lines can be clocked up to 480 Mbit/s (USB2.0) or 1.65 Gbit/s (HDMI). At such high data rates the transmission lines like cables or the line traces on the PCBs have to be very homogeneous regarding their surge impedance. This requires well defined trace dimensions as trace width and distance which have to be calculated depending on the requested surge impedance (e.g. 50 ) and the PCB material and layer dimensions. Any device connected to the data lines - like ESD-protection devices - have to be connected with minimal changes in these trace dimensions and distances. With the package in the so called Flow Through Design this is possible. The lines are running straight along the PCB while the VBUS054CD-FHI is placed on top without any vias or loops. Rev. 1.5, 15-Jul-15 Document Number: 81882 2 For technical questions, contact: ESDprotection vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 matched pair matched pair