RS485/EXTA FREE TRANSCEIVER RXM-01 MOUNTING CONNECTION INSTRUCTION MANUAL 1. Disconnect power supply by the phase fuse, the circuit-breaker or the switch- disconnector combined to the proper circuit. 2. Check if there is no voltage on con- nection cables by means of a special ZAMEL Sp. z o.o. measure equipment. 3. Instal RXM-01 device on a TH-35 rail in a distribution board. ul. Zielona 27, 43-200 Pszczyna, Poland 4. Connect the cables with the terminals in tel. +48 (32) 210 46 65, fax +48 (32) 210 80 04 accordance with the installing diagram. www.zamelcet.com, e-mail: marketing zamel.pl 5. Switch on the power supply from the mains. TECHNICAL DATA DESCRIPTION Transmission line between the control- ler and RXM-01 device is a shielded RXM-01 RXM device is used to control receiv- twisted pair (wire) - it is required to ers of wireless EXTA FREE system by Input (supply) terminals: L, N ground the line shield at one point. Re- D0 Input rated voltage: 230 V AC means of an industrial controller or a PC RT RT sistors (terminators) of 120 should Input voltage tolerance: -15 +10 % computer, equipped with RS-485 interface D1 be placed at the beginning and at the Nominal frequency: 50 / 60 Hz network, which use Modbus protocol to end of the line. Nominal power consumption: 0,49 W communicate. This device allows to add Optic signalling of input (supply): LED green diode EXTA FREE devices to the already exist- APPLICATION RS-485 communication terminals: A (D0), B (D1), C (common) ing wired installation (controlled by RS-485 Communication protocols: Modbus RTU, Modbus ASCII network) to increase range and possibili- Transmission speed: 2400, 4800, 9600, 19200 bit/s ties of the system without additional wires. RS485/EXTA FREE Parity: none, parity test, odd parity RXM-01 device in connection with an transceiver RXM-01 Network address: 0 (broadcast), 1 247 industrial controller allows to control auto- allows to transmit Optic sugnalling of RS-485 transmission: LED yellow diode control signals matically wireless receivers (creating light- Number of channels: 127 from PLC controller ing stages, automatic switch on or switch of (which is installed Transmission: radio 868,32 MHz devices at the adjusted time). in a distribution Coding way: unidirectional board) to wireless Coding: addressing transmission EXTA FREE control FEATURES Range: up to 300 m in the open area system devices o Ambient temperature range: -10 +55 C (ROP-01 radio cooperation with wireless EXTA FREE 2 receiver, SRP-02 Section of connecting cables: do 2,5 mm system transmitters and receivers, radio roller blinds Operating position: free cooperation with devices operating in controller). MODBUS standard (e.g. PLC program- Casing mounting: TH-35 rail (EN 60715) mable controllers, PC computers), Casing protection degree: IP20 (EN 60529) possibility of independent control up to Protection level: II 127 receivers, Overvoltage category: II mounting in a distribution board on a TH-35 rail, Pollution degree: 2 wide range of operation (up to 300 m), Surge voltage: 1 kV (EN 61000-4-5) sending information and power supply are Dimensions: monomodular casing (17,5 mm) 90 x 17,5 x 66 mm optically signalled, Weight: 0,070 kg connection possibility of external antenna ANT-01 not mounted in a distribution board, Reference standard: ETSI EN 300 220-1, ETSI EN 300 220-2, possibility of increasing operation range EN 60950, EN 61000 by means of RTN-01 retransmitter. APPEARANCE The device is designed for single-phase installation and must be installed in accordance with standards valid in a particu- Input (supply) terminals (L, N) lar country. The device should be connected according to the The ZAMEL company devices details included in this operat- CAUTION which are characterised Antenna ing manual. Installation, connection and control with this sign can cooperate should be carried out by a qualified electrician with each other. staff, who act in accordance with the service manual and the device functions. In case of casing dismantling an electric shock Optic signalling of input voltage may occur, and the guarantee is lost then. Before Optic signalling of RS-485 transmission installation make sure the connection cables are WARRANTY CARD not under voltage. The cruciform head screw- Antennas socket driver 3,5 mm should be used to instal the device. There is 24 months guarantee on the product Improper transport, storage, and use of the device 1. ZAMEL provides a two-year warranty for its products. influence its wrong functioning. It is not advisable Programming push-button 2. The ZAMEL warranty does not cover: a) mechanical defects resulting from transport, loading / unloading or other circumstances to instal the device in the following cases: if any b) defects resulting from incorrect installation or operation of ZAMEL products c) defects resulting from any changes made by CUS- device part is missing or the device is damaged or TOMERS or third parties, to products sold or equipment necessary for the correct operation of products sold d) defects resulting deformed. In case of improper functioning of the from force majeure or other aleatory events for which ZAMEL is not liable e) power supply (batteries) to be equipped with a device device contact the producer. in the moment of sale (if they appear) 3. All complaints in relation to the warranty must be provided by the CUSTOMER in writing to the retailer after discovering a defect. The symbol means selective 4. ZAMEL will review complaints in accordance with existing regulations. collecting of electrical and electronic 5. The way a complaint is settled, e.g. replacement of the product, repair or refund, is left to the discretion of ZAMEL. 6. Guarantee does not exclude, does not limit, nor does it suspend the rights of the PURCHASER resulting from the discrepancy equipment. between the goods and the contract. It is forbidden to put the used RS-485 (A, B, C) communication terminals equipment together with other waste. Salesman stamp and signature, date of sale VER. 004 11.07.2011OPERATION TRANSMITTERS PROGRAMMING RS-485 communication default parameters (default settings): Setting window (Com Params) of BitBoy programme Protocol: RTU Modbus (8 bits) 10110... 10110... Transmission speed: 9600 bps Parity: parity test (parity bit + stop bit) Network address: 1 Codes of Modbus function: FC03 - configuration register readout (transmission parameters, etc.) FC05 - output status setting (frame transmission with suitable push-button code) FC16 - (10 hex) - configuration registers record (transmission parameters record, etc.) Press PROG push-button of ROM-01 device Type push-button 1 pressing code in RXM-01 Type push-button 1 release code in FC05 - output status setting for a longer time until LED red diode switches on device. LED red diode of ROM-01 RXM-01 device. LED red diode of ROM-01 Register address Output value Push-button code (constant signal). Next release PROG push-button. switches on (first signal pulsates, switches on (signal pulsates) Base 0 Base 1 next the signal is constant). and then switches off std PLC - THE TRANSMITTER IS ADDED. FC05 example. Push-button 1 pressing code transmission. addressing addressing 00 00 00 01 FF 00 Push-button1 pressing 00 00 00 01 00 00 Push-button 1 release COOPERATION AND OPERATING RANGE 00 01 00 02 FF 00 Push-button 2 pressing 00 01 00 02 00 00 Push-button 2 release 01 05 00 00 FF 00 8C 3A Symbol ROP-01 ROP-02 ROB-01 SRP-02 SRP-03 RWG-01 RWL-01 ROM-01 ROM-10 RDP-01 RTN-01 00 7E 00 7E FF 00 Push-button 127 pressing 00 7E 00 7E 00 00 Push-button 127 release RNK-02 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m RNK-04 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m 01 05 00 00 FF 00 8C 3A FC03 and FC16 - register configuration readout/record 01 05 00 00 FF 00 8C 3A P-256/8 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m Register address Register Push-button code Transmitted frame: P-257/4 (2) 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m content Address Function code Register address Data CRC16 sum Base 0 Base 1 0x01 0x05 0x00 0x00 0xFF 0x00 0x8C 0x3A RNM-10 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m std PLC Received frame: addressing addressing 0x01 0x05 0x00 0x00 0xFF 0x00 0x8C 0x3A RNP-01 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m 00 00 00 01 Wired Bits 1:0: Bits 1:0 Transmission speed (bit/sec.) RNP-02 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m transmission 00=2400 FC05 example: Push-button 1 release code transmission. parameters RNL-01 160 m 180 m 180 m lack* lack* 200 m 160 m 200 m 200 m 160 m 200 m 01=4800 10=9600 RTN-01 200 m 200 m 200 m 200 m 200 m 250 m 200 m 250 m 250 m 200 m 250 m 11=19200 RCR-01 160 m 180 m 180 m lack* lack* 200 m 160 m 200 m 200 m 160 m 200 m Bits 3:2 sign error control 00 and 11 = none RTI-01 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m 01 05 00 00 00 00 CD CA 01=odd parity test RXM-01 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m 10=parity test Bit 4 Transmission mode * - 1-channel transmitters do not cooperate with roller blind controllers.. 0=RTU Modbus CAUTION: The given range concerns open area - an ideal condition without any natural or artificial obstacles. If there are some obstacles between a transmitter and a re - 1=ASCII Mosdbus 01 05 00 00 00 00 CD CA ceiver, it is advisable to decrease the range according to: wood and plaster: from 5 to 20 %, bricks: from 10 to 40 %, reinforced concrete: from 40 to 80 %, 00 01 00 02 Modbus Bits 7:0 Values from 1 to 247 01 05 00 00 00 00 CD CA metal: from 90 to 100 % , glass: from 10 to 20 %, Over- and underground medium and high electrical power lines, radio and television transmitters, GSM transmitters set address close to a device system have also a negative influence on the range. Transmitted frame: Address Function code Register address Data CRC16 sum 00 02 00 03 Register 0=unblocking, 1=blocking RANGE LOSS CONCERNING RADIO SIGNALS GOING THROUGH OBSTACLES 0x01 0x05 0x00 0x00 0x00 0x00 0xCD 0xCA record Bit 0 Blocking of wired transmission parameters Received frame: blockade record 0x01 0x05 0x00 0x00 0x00 0x00 0xCD 0xCA Bit 1 Blocking of Modbus address record FC03 example. Register readout FC03 example: Registers record. bricks: from 10 to 40 % wood and plaster: from 5 to 20 % reinforced concrete: from 40 to 80 % metal: from 90 to 100% glass: from 10 to 20 % 01 03 00 00 00 03 05 CB 01 10 00 02 00 01 02 00 02 26 73 TRANSMITTERS RECEIVERS RNK-02 RNL-01 ROP-01 RWL-01 2channel button Radio 1-channel Radio lighting radio transmitter foot transmitter radio receiver switch 01 03 00 00 00 03 05 CB 01 10 00 02 00 01 02 00 02 26 73 01 03 06 00 0A 00 01 00 03 A8 B5 01 10 00 02 00 01 A0 09 RNK-04 RTI-01 ROP-02 RWG-01 Transmitted frame: Transmitted frame: 4-channel button IR/EXTA FREE 2-channel Remote control Address Function Start Number of registers CRC16 Address Function Start Number Number of Data CRC16 radio transmitter transceiver radio receiver socket code address to readout sum code address of bits regs. to record sum 0x01 0x03 0x00 0x00 0x00 0x03 0x05 0xCB 0x01 0x10 0x00 0x02 0x00 0x01 0x02 0x00 0x02 0x26 0x73 Received frame: Received frame: P-256/8 RNM-10 RDP-01 SRP-02 Address Function Number Parameters Modbus Register CRC16 Address Function Start Number of Data CRC16 8-channel 4-channel radio 1-channel Radio roller blinds code of bits address blockade sum code address regs. to record sum remote control modular transmitter radio dimmer controller 0x01 0x03 0x06 0x00 0x0A 0x00 0x01 0x00 0x03 0xA8 0xB5 0x01 0x10 0x00 0x02 0x00 0x01 0xA0 0x09 CAUTION: In order to change transmission parameters it is necessary to delete a suitable blockade bit record of configuration registers. P-257/4 RNP-01 ROB-01/12-24V SRP-03 After content change in configuration registers, transmission parameters are updated just after a reply is sent (in broadcast mode the device does 4-channel 4-channel Radio Central radio roller remote control radio transmitter gate controller blinds controller not send replies). P-257/2 RNP-02 ROM-01 ROM-10 PC computer equipped in RS-485 interface card can take place of a controller (it is possible to use a converter RS-485 instead of RS-23 or USB) or a suitable 2-channel 4-channel 1-channel radio 2-channel software (e.g. BitBoy application). remote control radio transmitter modular receiver radio modular receiver RCR-01 RXM-01 RESET PUSH-BUTTON Radio RS-485/EXTA FREE motion sensor Transceiver 1 short pressing (<2 sec.): radio transmission of push-button 1 pressing code. ACCESSORIES 2 short pressings (<2 sec each): radio transmission of push-button 1 release code. 1 long pressing (>2 sec.): device RESET. 2 short pressings (<2 sec. each) + 1 long pressing (>2 sec.): device RESET - return to default settings ANT-01 RTN-01 (Modbus address, transmission parameters). External antenna Retransmitter LED green diode flashing - chosen pressing combination has been confirmed. VER. 004 11.07.2011