NSP4201MR6 ESD and Surge Protection Device Low Clamping Voltage Surge Protection Diode Array www.onsemi.com The NSP4201MR6 surge protector is designed to protect high speed data lines from ESD, EFT, and lightning surges. 6 Features 1 Protection for the Following IEC Standards: TSOP6 IEC 6100042 (ESD) 30 kV (Contact) CASE 318G IEC 6100045 (Lightning) 25 A (8/20 s) Low Clamping Voltage MARKING DIAGRAM Low Leakage UL Flammability Rating of 94 V0 42 M SZ Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements AECQ101 Qualified and PPAP Capable 42 = Specific Device Code These Devices are PbFree, Halogen Free/BFR Free and are RoHS M = Date Code Compliant = PbFree Package (Note: Microdot may be in either location) Typical Applications *Date Code orientation may vary High Speed Communication Line Protection depending upon manufacturing location. USB 1.1 and 2.0 Power and Data Line Protection Digital Video Interface (DVI) PIN CONFIGURATION AND SCHEMATIC Monitors and Flat Panel Displays I/O 1 6 I/O MAXIMUM RATINGS (T = 25C unless otherwise noted) J Rating Symbol Value Unit V 2 5 V N P Peak Power Dissipation P 500 W pk 8/20 s T = 25C (Note 1) A I/O 3 4 I/O Operating Junction Temperature Range T 40 to +125 C J Storage Temperature Range T 55 to +150 C stg Lead Solder Temperature T L Maximum (10 Seconds) 260 C ORDERING INFORMATION IEC 6100042 Air (ESD) ESD 30 kV Device Package Shipping IEC 6100042 Contact (ESD) 30 NSP4201MR6T1G TSOP6 3000 / Tape & IEC 6100044 (5/50 ns) EFT 40 A (PbFree) Reel Stresses exceeding those listed in the Maximum Ratings table may damage the SZNSP4201MR6T1G TSOP6 3000 / Tape & device. If any of these limits are exceeded, device functionality should not be (PbFree) Reel assumed, damage may occur and reliability may be affected. 1. Nonrepetitive current pulse per Figure 1 (Pin 5 to Pin 2) For information on tape and reel specifications, including part orientation and tape sizes, please See Application Note AND8308/D for further description of refer to our Tape and Reel Packaging Specification survivability specs. Brochure, BRD8011/D. Semiconductor Components Industries, LLC, 2017 1 Publication Order Number: June, 2017 Rev. 1 NSP4201MR6/DNSP4201MR6 ELECTRICAL CHARACTERISTICS I (T = 25C unless otherwise noted) A I F Symbol Parameter I Maximum Reverse Peak Pulse Current PP V Clamping Voltage I C PP V Working Peak Reverse Voltage RWM V V V C BR RWM V I V I Maximum Reverse Leakage Current V R F R RWM I T V Breakdown Voltage I BR T I Test Current T I Forward Current F I PP V Forward Voltage I F F P Peak Power Dissipation pk UniDirectional Surge Protection C Capacitance V = 0 and f = 1.0 MHz R *See Application Note AND8308/D for detailed explanations of datasheet parameters. ELECTRICAL CHARACTERISTICS (T =25C unless otherwise specified) J Parameter Symbol Conditions Min Typ Max Unit Reverse Working Voltage V (Note 2) 5.0 V RWM Breakdown Voltage V I =1 mA, (Note 3) 6.0 V BR T Reverse Leakage Current I V = 5 V 1.0 A R RWM Clamping Voltage V V I = 1 A, Any I/O to GND 8.5 C PP (t = 8/20 s per Figure 1) p I = 5 A, Any I/O to GND 9.0 PP I = 8 A, Any I/O to GND 10 PP I = 25 A, Any I/O to GND 12 PP Junction Capacitance C V = 0 V, f=1 MHz between I/O Pins and GND 3.0 5.0 pF J R Junction Capacitance C V = 0 V, f=1 MHz between I/O Pins 1.5 3.0 pF J R 2. Surge protection devices are normally selected according to the working peak reverse voltage (V ), which should be equal or greater RWM than the DC or continuous peak operating voltage level. 3. V is measured at pulse test current I . BR T 20 100 t PEAK VALUE I 8 s r RSM 90 18 PULSE WIDTH (t ) IS DEFINED P 16 80 AS THAT POINT WHERE THE 14 70 PEAK CURRENT DECAY = 8 s 60 12 HALF VALUE I /2 20 s RSM I/OGND 50 10 40 8 6 30 t P 4 20 10 2 0 0 020 40 60 80 05 10 15 20 25 30 PEAK PULSE CURRENT (A) t, TIME ( s) Figure 1. IEC6100045 8/20 s Pulse Waveform Figure 2. Clamping Voltage vs. Peak Pulse Current (t = 8/20 s per Figure 1) p www.onsemi.com 2 % OF PEAK PULSE CURRENT CLAMPING VOLTAGE (V)