Datasheet Serial EEPROM Series Standard EEPROM WLCSP EEPROM BRCB016GWL-3 General Description 2 BRCB016GWL-3 is a serial EEPROM of I C BUS Interface Method Features Package W(Typ) x D(Typ) x H(Max) 2 Completely conforming to the world standard I C BUS. UCSP50L1 1.10mm x 1.15mm x 0.55mm All controls available by 2 ports of serial clock (SCL) and serial data (SDA) 1.7V to 3.6V single power source operation most suitable for battery use 1.7V to 3.6V wide limit of operating voltage, possible FAST MODE 400KHz operation 16byte Page Write Mode useful for initial value write at factory shipment Self-timed Programming Cycle Low Current Consumption Prevention of Write Mistake at Low Voltage More than 1 million write cycles More than 40 years of data retention Noise Filter built in SCL / SDA terminal Initial delivery state FFh BRCB016GWL-3 Capacity Bit Format Type Power Source Voltage Package 16Kbit 2K8 BRCB016GWL-3 1.7V to 3.6V UCSP50L1 Product structureSilicon monolithic integrated circuit This product has no designed protection against radioactive rays www.rohm.com TSZ02201-0R2R0G100260-1-2 2013 ROHM Co., Ltd. All rights reserved. 1/26 TSZ2211114001 25.Feb.2013 Rev.002Datasheet BRCB016GWL-3 Absolute Maximum Ratings (Ta=25C) Parameter Symbol Rating Unit Remark Supply Voltage V -0.3 to +6.5 V CC Power Dissipation Pd 220 (UCSP50L1) mW Derate by 2.2mW/C when operating above Ta=25C Storage Temperature Tstg -65 to +125 C Operating Temperature Topr -40 to +85 C The Max value of Input Voltage / Output Voltage is not over 6.5V. Input Voltage/ -0.3 to Vcc+1.0 V When the pulse width is 50ns or less, the Min value of Input Voltage Output Voltage / Output Voltage is not below -1.0V. Junction Temperature Tjmax 150 C Junction temperature at the storage condition Memory Cell Characteristics (Ta=25C, Vcc=1.7V to 3.6V) Limit Parameter Unit Min Typ Max (1) 1,000,000 - - Times Write Cycles (1) 40 - - Years Data Retention (1) Not 100% TESTED Recommended Operating Ratings Parameter Symbol Rating Unit Power Source Voltage Vcc 1.7 to 3.6 V Input Voltage V 0 to Vcc IN DC Characteristics (Unless otherwise specified, Ta=-40 to +85, Vcc=1.7V to 3.6V) Limit Parameter Symbol Unit Conditions Min Typ Max Input High Voltage V 0.7Vcc - Vcc+1.0 V 1.7VVcc3.6V IH (2) Input Low Voltage V -0.3 - +0.3Vcc V 1.7VVcc3.6V IL Output Low Voltage1 V - - 0.4 V I =3.0mA, 2.5VVcc3.6V (SDA) OL1 OL Output Low Voltage2 V - - 0.2 V I =0.7mA, 1.7VVcc2.5V (SDA) OL2 OL Input Leakage Current I -1 - +1 A V =0 to Vcc LI IN Output Leakage Current I -1 - +1 A V =0 to Vcc (SDA) LO OUT Vcc=3.6V, f L=400kHz, t =5ms, SC WR Supply Current (Write) I - - 2.0 mA CC1 Byte Write, Page Write Vcc=3.6V, f =400kHz SCL Supply Current (Read) I - - 0.5 mA Random Read, Current Read, Sequential CC2 Read Standby Current I - - 2.0 A Vcc=3.6V, SDASCL=Vcc, WP=GND SB (2) When the pulse width is 50ns or less, it is -1.0V. www.rohm.com TSZ02201-0R2R0G100260-1-2 2013 ROHM Co., Ltd. All rights reserved. 2/26 TSZ2211115001 25.Feb.2013 Rev.002