CRG01,CRG02
TOSHIBA Rectifier Silicon Diffused Type
CRG01, CRG02
General Purpose Rectifier Applications
Unit: mm
Average forward current: I = 0.7 A
F (AV)
Repetitive peak reverse voltage: V = 100 V, 400 V
RRM
Suitable for compact assembly due to small surface-mount package
TM
SFLAT (Toshiba package name)
Absolute Maximum Ratings (Ta = 25C)
Characteristics Symbol Rating Unit
CRG01 100
Repetitive peak reverse
V V
RRM
voltage
CRG02 400
Average forward current I 0.7 A
F(AV)
15 (50 Hz)
Peak one cycle surge forward current
I A
FSM
(non-repetitive)
16.5 (60 Hz)
JEDEC
Junction temperature T 40~150 C
j
JEITA
Storage temperature T 40~150 C
stg
TOSHIBA 3-2A1A
Note: Using continuously under heavy loads (e.g. the application of high
Weight: 0.013 g (typ.)
temperature/current/voltage and the significant change in
temperature, etc.) may cause this product to decrease in the
reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are
within the absolute maximum ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(Handling Precautions/Derating Concept and Methods) and individual reliability data (i.e. reliability test report
and estimated failure rate, etc).
Electrical Characteristics (Ta = 25C)
Characteristics Symbol Test Condition Typ. MaxUnit
V I = 0.1 A 0.88
FM (1) FM
Peak forward voltage V
V I = 0.7 A 1.1
FM (2) FM
V I = 1.0 A 1.1
FM (3) FM
Repetitive peak reverse current I V = Rated 10 A
RRM RRM
Device mounted on a ceramic board
65
(soldering land: 2 mm 2 mm)
Thermal resistance r C/W
th (j-a)
Device mounted on a glass-epoxy board
130
(soldering land: 6 mm 6 mm)
2006-11-06
1CRG01,CRG02
Marking
Abbreviation Code Part No.
G1 CRG01
G2 CRG02
Standard Soldering Pad
Unit: mm
1.2
1.2
2.8
Handling Precaution
The absolute maximum ratings denote the absolute maximum ratings, which are rated values and must not be
exceeded during operation, even for an instant. The following are the general derating methods that we recommend
when you design a circuit with a device.
V : We recommend that the worst case voltage, including surge voltage, be no greater than 80% of the
RRM
absolute maximum rating of V for a DC circuit and be no greater than 50% of that of V for
RRM RRM
an AC circuit. V has a temperature coefficient of 0.1%/C. Take this temperature coefficient into
RRM
account designing a device at low temperature.
I : We recommend that the worst case current be no greater than 80% of the absolute maximum rating
F(AV)
of I . Carry out adequate heat design. If you cant design a circuit with excellent heat radiation,
F(AV)
set the margin by using an allowable Tamax-I curve.
F(AV)
This rating specifies the non-repetitive peak current in one cycle of a 50-Hz sine wave, condition angle 180.
Therefore, this is only applied for an abnormal operation, which seldom occurs during the lifespan of the device.
We recommend that a device be used at a Tj of below 120C under the worst load and heat radiation conditions.
Thermal resistance between junction and ambient fluctuates depending on the devices mounting condition. When
using a device, design a circuit board and a soldering land size to match the appropriate thermal resistance value.
Please refer to the Rectifiers databook for further information.
2006-11-06
2