TLP2066 TOSHIBA PHOTOCOUPLER GaA As IRED & PHOTO-IC TLP2066 FA (Factory Automation) Unit: mm High Speed Interface 3.3V Supply Voltage The Toshiba TLP2066 consists of a GaAAs light-emitting diode and an integrated high-gain, high-speed photodetector. TLP2066 operates with 3.3 V supply voltage. Toshiba offers TLP116 for supply voltage 5V type. Inverter logic (totem pole output) Package type : MFSOP6 Guaranteed performance over temperature : -40 to 100C Power supply voltage : 3.0 to 3.6V Input threshold current: I =5mA (max) FHL Propagation delay time (t /t ): 60ns (max) pHL pLH Switching speed : 20MBd (typ.) (NRZ) JEDEC Common mode transient immunity : 15 kV/s JEITA TOSHIBA 11-4C2 Isolation voltage : 3750 V rms Weight: 0.09 g (typ.) UL Recognized : UL1577, File No. E67349 cUL Recognized : CSA Component Acceptance Service No.5A Pin Configuration (top view) Option (V4) 1 6 1: ANODE V VDE approved : EN60747-5-2 CC Maximum operating insulation voltage : 565 Vpk 3: CATHODE Highest permissible over voltage : 6000 Vpk 5 4: GND (Note) When a EN60747-5-2 approved type is needed, 5: V O GND please designate the Option(V4) 3 4 6: V CC SHIELD Schematic I Truth Table CC V CC 6 Input LED Tr1 Tr2 Output I F Tr1 1+ H ON OFF ON L I O V F V L OFF ON OFF H O 3- Tr2 5 GND SHIELD 4 A 0.1F bypass capacitor must be connected between pins 6 and 4. Start of commercial production 2007/08 1 2014-09-01 TLP2066 Absolute Maximum Ratings (Ta=25C) Characteristic SymbolRating Unit Forward current I 25 mA F Forward current derating (Ta 85C) I / Ta -0.63 mA/C F Peak transient forward current (Note 1) I 1 A FPT Reverse voltage V 5 V R Output current (Note 2) I 10 mA O Output voltage V 6 V O Supply voltage V 6 V CC Output power dissipation P 40 mW O Operating temperature range T -40 to 100 C opr Storage temperature range T -55 to 125 C stg Lead solder temperature (10s) T 260 C sol Isolation voltage (AC,1minute, R.H. 60%, Ta=25C) (Note 3) BV 3750 V S rms Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (Handling Precautions/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 1: Pulse width P 1s, 300pps. W Note 2: Derate 0.25 mA/C above 85C. Note 3: This device is regarded as a two-terminal device: pins 1 and 3 are shorted together, as are pins 4, 5 and 6. Recommended Operating Conditions Characteristic Symbol Min Typ. Max Unit Input current , ON I 8 18 mA F(ON) Input voltage , OFF V 0 0.8 V F(OFF) Supply voltage(*) (Note 4) 3.0 3.3 3.6 V V CC (*) This item denotes operating ranges, and does not imply recommended operating conditions. Note: Recommended operating conditions are given as a design guideline to obtain the expected performance of the device. In addition, each item is an independent guideline. In developing designs using this product, please confirm the specified characteristics shown in this document. Note 4: The detector of this product requires a power supply voltage (V ) of 3.0 V or higher for stable operation. CC If V is lower than this value, I may increase, or the output may become unstable. CC CCH Be sure to check the supply current, and the on/off operation of the power supply before using the product. Note 5: A ceramic capacitor (0.1 F) should be connected from pin 6 to pin 4 to stabilize the operation of the high gain linear amplifier. Failure to do so may impair the switching property. The total lead length between the capacitor and the photocoupler should not exceed 1 cm. 2 2014-09-01 LED DETECTOR