RETRANSMITTER RTN-01 MANUAL INSTRUCTION ZAMEL Sp. z o.o. ul. Zielona 27, 43-200 Pszczyna, Poland tel. +48 (32) 210 46 65, fax +48 (32) 210 80 04 www.zamelcet.com, e-mail: marketing zamel.pl DESCRIPTION TECHNICAL DATA RTN-01 RTN-01 retransmitter is used to in- crease radio transmitter signal range Input rated voltage: 230 V~ Input voltage tolerance: -15 +10 % of wireless EXTA FREE control sys- Nominal frequency: 50 / 60 Hz tem. Up to four retransmitters can op- Nominal power consumption: 0,45 W erate in a system - it gives the possi- Optic signalling of supply voltage: LED green diode bility to increase the distance between Maximum load current of socket output: 16 A a transmitter and a receiver to 1000 m. Transmission: radio 868,32 MHz The device is equipped with a 230V Coding way: unidirectional AC pass-through socket - every re- Coding: addressing transmission ceiver can be connected to it. The re- Maximum number of transmitters: 32 transmitter does not block the socket. Range: up to 250 m in the open area Optic signalling of transmitters operation: LED red diode o Ambient temperature range: -10 +55 C Operating position: free Casing mounting: 230 V~ socket Casing protection degree: IP20 (EN 60529) FEATURES Protection level: II Kategoria przepiciowa: II wider operation range of EXTA FREE Pollution degree: 2 radio devices, Surge voltage: 1 kV (EN 61000-4-5) possibility to cooperate with three oth- Dimensions: 160 x 66 x 90 mm er RTN-01 retransmitters, Weight: 0,180 kg easy mounting in 230V AC socket, Reference standard: ETSI EN 300 220-1, ETSI EN 300 220-1, low current consumption, possibility of EN 60950, EN 61000 constant work, wide range of operation (up to 250 m), APPEARANCE power supply and radio transmission are optically signalled. Antenna The device is designed for single-phase installation and must be installed in Optic signalling of power supply accordance with standards Optic signalling of radio transmission valid in a particular country. The device should be con- nected according to the de- CAUTION Programming push-button tails included in this operat- ing manual. Installation, connection and control should be carried out by a qualified electrician 230 V~ socket staff, who act in accordance with the service manual and the device functions. 230 V~ power supply plug In case of casing dismantling an electric shock may occur, and the guarantee is lost then. Before installation make sure the connection cables are not under voltage. The cruciform head screwdriver 3,5 mm should be used to in- stal the device. Improper transport, storage, and Retransmitters use of the device influence its wrong functioning. number switch It is not advisable to instal the device in the fol- lowing cases: if any device part is missing or the device is damaged or deformed. In case of improper functioning of the device contact the producer. The symbol means selective collecting of electrical and electronic equipment. It is forbidden to put the used equipment together with other waste. VER. 004 11.07.2011r r e e v t i t e i OPERATION Fig. 1. Possible switch settings. Before retransmitters operation start it is important to set switches, which are in the back part of a device, according to a suitable com- bination. If only one retransmitter is used its switches should be set in combinationa presented in Fig. 1. CAUTION Only 4 retransmitters can operate in the transmitters operation range. In a situation where few retransmitters are used (maximum 4), the a b c d switch of the following retransmitter should be set in a combination dif- ferent from the combination of the other retransmitters. Suggested setting sequence for the following retransmitters according to Fig. 1. The ZAMEL company devices which are characterised with this sign can cooperate with each other. Fig. 2. Operation with maximum number of retransmitters. PROGRAMMING RADIO TRANSMITTERS ADDITION (An exemplary programming procedure of P-257/2 remote control) Press PROG push-button of RTN-01 device Press and release transmitters push-button. Press and release the same transmitters for a longer time until LED red diode switches on LED red diode switches on (first signal push-button. LED red diode switches on (constant signal). Next release PROG push-button. pulsates, next the signal is constant). (the signal pulsates) and next it switches off - THE TRANSMITTER IS ADDED. CAUTION By adding next retransmitters to increase the range of one transmitter, it is required to add this transmitter to every retransmitter. One transmitter can be added to a retransmitter during one programming cycle. RADIO TRANSMITTERS DELETION Press PROG push-button of RTN-01 After 5 seconds LED red diode switches on Release the push-button in RTN-01 - device for a longer time. (signal pulsates) and then it switches off. MEMORY IS DELETED. COOPERATION AND OPERATING Symbol ROP-01 ROP-02 ROB-01 SRP-02 SRP-03 RWG-01 RWL-01 ROM-01 ROM-10 RDP-01 RTN-01 RNK-02 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m RNK-04 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m P-256/8 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m P-257/4 (2) 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m RNM-10 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m RNP-01 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m RNP-02 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m RNL-01 160 m 180 m 180 m lack* lack* 200 m 160 m 200 m 200 m 160 m 200 m RTN-01 200 m 200 m 200 m 200 m 200 m 250 m 200 m 250 m 250 m 200 m 250 m RCR-01 160 m 180 m 180 m lack* lack* 200 m 160 m 200 m 200 m 160 m 200 m RTI-01 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m RXM-01 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m * - 1-channel transmitters do not cooperate with roller blind controllers. CAUTION: The given range concerns open area - an ideal condition without any natural or artificial obstacles. If there are some obstacles between a transmitter and a receiver, it is advisable to decrease the range according to: wood and plaster: from 5 to 20 %, bricks: from 10 to 40 %, reinforced concrete: from 40 to 80 %, metal: from 90 to 100%, glass: from 10 to 20 %. Over- and underground medium and high electrical power lines, radio and television transmitters, GSM transmitters set close to a device system have also a negative influence on the range. WARRANTY CARD There is 24 months guarantee on the product 1. ZAMEL provides a two-year warranty for its products. 2. The ZAMEL warranty does not cover: a) mechanical defects resulting from transport, loading / unloading or other circumstances b) defects resulting from incorrect installation or operation of ZAMEL products c) defects resulting from any changes made by CUS- TOMERS or third parties, to products sold or equipment necessary for the correct operation of products sold d) defects resulting from force majeure or other aleatory events for which ZAMEL is not liable e) power supply (batteries) to be equipped with a device in the moment of sale (if they appear) 3. All complaints in relation to the warranty must be provided by the CUSTOMER in writing to the retailer after discovering a defect. 4. ZAMEL will review complaints in accordance with existing regulations. 5. The way a complaint is settled, e.g. replacement of the product, repair or refund, is left to the discretion of ZAMEL. 6. Guarantee does not exclude, does not limit, nor does it suspend the rights of the PURCHASER resulting from the discrepancy between the goods and the contract. Salesman stamp and signature, date of sale m c e s n R a r T