TLP2116 TOSHIBA PHOTOCOUPLER IRED & PHOTO-IC TLP2116 Plasma Display Panels (PDP) Unit: mm High-Speed Interfaces Factory Automation (FA) The TOSHIBA TLP2116 dual photocoupler consists of a pair of an infrared emitting diodes optically coupled to integrated high gain and high-speed photodetectors. Inverter logic (totem-pole output) Package: SO8 Guaranteed performance over temperature : -40 to 100C Power supply voltage: 4.5 to 5.5 V Input thresholds current: I = 5 mA (max) FHL Propagation delay time (tpHL/tpLH): 75 ns (max) Switching speed: 15 MBd (typ.) (NRZ) Common mode transient immunity: 10 kV/ s Isolation voltage: 2500 Vrms JEDEC UL-recognized: UL 1577, File No.E67349 JEITA cUL-recognized: CSA Component Acceptance Service No.5A TOSHIBA 11 5K1S Weight: 0.11 g (typ.) File No.E67349 VDE-approved: EN 60747-5-5 (Note 1) Note 1 : When a VDE approved type is needed, Please designate the Option(V4). Pin Configuration (Top View) Truth Table 1:ANODE 1 1 VCC 8 Input LED1(2) Tr1(3) Tr2(4) Output 1(2) 2:CATHODE 1 ON OFF ON L H 3:CATHODE 2 2 7 L OFF ON OFF H 4:ANODE 2 5:GND Schematic 6 3 6:V 2(Output2) O I CC 8 7:V 1(Output1) O GND 5 V 4 CC 8:V SHIELD CC I 1 F Tr1 1 7 I 1 O V 1 O 2 Tr2 SHIELD Tr3 3 6 I 2 O VF2 V 2 O 4 Tr4 I 2 F 5 GND SHIELD Start of commercial production A bypass capacitor of 0.1 F must be 2008-02 connected between pins 8 and 5. 2019 1 2019-06-03 Toshiba Electronic Devices & Storage Corporation TLP2116 Absolute Maximum Ratings (Ta=25C) Characteristic Symbol Rating Unit Forward current (Each Channel) I 20 mA F Forward current derating (Ta 85C) (Each Channel) I /Ta -0.5 mA/C F Peak transient forward current (Each Channel) (Note 1) I 1 A FPT Reverse voltage (Each Channel) V 5 V R Input Power Dissipation (Each Channel) P 40 mW D Input Power Dissipation Derating (E ac h Channel) PD/C -1.0 mW/C (Ta85C) Output current (Each Channel) I 10 mA O Output voltage (Each Channel) V 6 V O Supply voltage V 6 V CC Output power dissipation (Each P 40 mW O Channel) Output Power Dissipation Derating (Ta 85C) (Each Channel) PO/C -1.0 mW/C Operating temperature range T -40 to 100 C opr Storage temperature range T -55 to 125 C stg Lead solder temperature (10 s) T 260 C sol Isolation voltage (AC,60 s, R.H. 60 %,) (Note 2) BV 2500 Vrms S Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (Handling Precautions/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 1: Pulse width PW 1 s, 300 pps. Note 2: This device is regarded as a two terminal device: pins 1, 2, 3 and 4 are shorted together, as are pins 5, 6, 7 and 8. Recommended Operating Conditions Characteristic Symbol Min Typ. Max Unit Input current, ON (Each Channel) I 8 18 mA F(ON) Input voltage, OFF (Each Channel) V 0 0.8 V F(OFF) Supply voltage(*) (Note 3) V 4.5 5.0 5.5 V CC Operating temperature T -40 100 C opr (*) This item denotes operating ranges, not meaning of recommended operating conditions. Note 3: The detector of this product requires power supply voltage (V ) of 4.5 V or higher for stable operation. CC If the V is lower than this value, I may increase, or output may be unstable. CC CCH Be sure to use the product after checking the supply current, and the operation of a power-on/-off. Note: A ceramic capacitor (0.1 F) should be connected from pin 8 (VCC) to pin 5 (GND) to stabilize the operation of the high gain linear amplifier. Failure to provide the bypass may impair the switching property. The total lead length between capacitor and coupler should not exceed 1 cm. 2019 2 2019-06-03 Toshiba Electronic Devices & Storage Corporation DETECTOR LED