TLP2166A TOSHIBA PHOTOCOUPLER IRED & PHOTO-IC TLP2166A Plasma Display Panels (PDPs) Unit: mm High-Speed Interfaces 3.3-V Voltage Source The Toshiba TLP2166A consists of an infrared emitting diode and an integrated high-gain, high-speed photodetector. The TLP2166A is housed in the 8-pin SO package. Since the TLP2166A contains two photocouplers, it saves board space. The TLP2166A operates with a 3.3-V supply voltage. Inverting logic output (totem-pole output) SO8 package Guaranteed performance over -40 to 100C Power supply voltage: 3.0 to 3.6 V Input threshold current: I = 3 mA (max) FHL Switching time (t / t ): 75 ns (max) pHL pLH JEDEC Switching speed: 15 MBd (typ.)(NRZ) JEITA Common-mode transient immunity: 15 kV/ s TOSHIBA 11 5K1S Weight: 0.11 g (typ.) Isolation voltage: 2500 V rms UL-recognized: UL 1577, File No.E67349 cUL-recognized: CSA Component Acceptance Service No.5A File No.E67349 VDE-approved: EN 60747-5-5 (Note 1) Note 1 : When a VDE approved type is needed, please designate the Option(V4). Truth Table Input LED1(2) M1(3) M2(4) Output 1(2) H ON OFF ON L Pin Configuration (Top View) L OFF ON OFF H 1: ANODE 1 1 8 V Schematic CC 2: CATHODE 1 I 8 CC 3: CATHODE 2 7 2 V CC 4: ANODE 2 I F1 5: GND M1 6 3 1 6: V (Output2) O2 7 I O1 7: V (Output1) V GND O1 F1 V 4 5 O1 8: V 2 CC M2 SHIELD LED1 SHIELD A bypass capacitor of 0.1F must be connected between pins 8 and 5. M3 LED2 3 6 I O2 V F2 V O2 4 M4 I F2 5 Start of commercial production GND 2008-07 SHIELD 2019 1 2019-06-03 Toshiba Electronic Devices & Storage Corporation TLP2166A Absolute Maximum Ratings (Ta=25C) CHARACTERISTIC SYMBOL RATING UNIT Forward Current (Note 1) I 15 mA F Forward Current Derating (Ta 95C) (Note 1) I / Ta -0.5 mA/C F Peak Transient Forward Current (Note 1, 2) I 1 A FP Reverse Voltage (Note 1) V 5 V R Input Power Dissipation (Note 1) P 40 mW D Input Power Dissipation Derating (Ta 95C) (Note 1) P /C -1.3 mW/C D Output Current (Note 1) IO 10 mA Output Voltage (Note 1) V 6 V O Supply Voltage V 6 V CC Output Power Dissipation P 40 mW O Output Power Dissipation Derating (Ta 25C) P /C -0.4 mW/C O Operating Temperature Range T -40 to 100 C opr Storage Temperature Range T -55 to 125 C stg Lead Soldering Temperature (10 s) T 260 C sol Isolation Voltage (AC, 60 s, R.H. 60 %) (Note 3) BV 2500 V S rms Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (Handling Precautions/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 1: Each Channel. Note 2: Pulse width 1 s, 300 pps. Note 3: This device is regarded as a two terminal device: pins 1, 2, 3 and 4 are shorted together, as are pins 5, 6, 7 and 8. Recommended Operating Conditions CHARACTERISTIC SYMBOL MIN TYP. MAX UNIT Input Current, ON (Note 1) I 5 10 mA F(ON) Input Voltage, OFF (Note 1) V 0 0.8 V F(OFF) Supply Voltage* (Note 4) V 3.0 3.3 3.6 V CC Operating Temperature T -40 100 C opr * This item denotes operating range, not meaning of recommended operating conditions. Note 4: The detector of this product requires a power supply voltage (VCC) of 3.0 V or higher for stable operation. If the VCC is lower than this value, an ICCH may increase, or an output may be unstable. Be sure to use the product after checking the supply current, and the operation of a power-on/-off Note: A ceramic capacitor (0.1 F) should be connected from pin 8 (V ) to pin 5 (GND) to stabilize the operation of CC the high gain linear amplifier. Failure to provide the bypass may impair the switching property. The total lead length between capacitor and coupler should not exceed 1 cm. 2019 2 2019-06-03 Toshiba Electronic Devices & Storage Corporation DETECTOR LED