D1U4CS-W-2200-12-HxxC Series www.murata-ps.com AC/DC Front End Power Supply PRODUCT OVERVIEW The D1U4CS-W-2200-12-HxxC is a 2200 Watt, power-factor-corrected (PFC) front-end power supply for hot-swap- ping redundant systems. The main output is 12V with a standby output of 5V or 3.3V. Packaged in a 1U low pro le enclosure, it is designed to deliver reliable bulk power to servers, workstations, storage systems or any 12V distrib- uted power architecture systems requiring high power density. The highly ef cient electrical and thermal design with internal cooling fans supports reliable operation conditions. The D1U4CS-W-2200-12-HxxC is designed to autorecover 2 from overtemperature fault. Status information is provided with front panel LEDs, logic signals and an I C manage- ment interface. Four units can be packaged into an optional 19 1U power shelf to provide up to 8.8kW of power. ORDERING GUIDE Power Output Power Output Main Standby Model Number Air ow High Line AC Low Line AC Output Output D1U4CS-W-2200-12-HC4C 2200W 1100W 12.12V 3.3V Back to front D1U4CS-W-2200-12-HC3C 2200W 1100W 12.12V 3.3V Front to back FEATURES D1U4CS-W-2200-12-HA4C 2200W 1100W 12.12V 5V Back to front 2200W (220Vac), 1100W (110Vac) D1U4CS-W-2200-12-HA3C 2200W 1100W 12.12V 5V Front to back Output Power SM INPUT CHARACTERISTICS Certi ed to Climate Savers Computing Initiative and 80 PLUS Gold ef ciency Parameter Conditions Min. Typ. Max. Units Input Voltage Operating Range 90 115/230 264 Vac 12V Main Output, 3.3V or 5V Standby Output Input Frequency 47 60 63 Hz 1U height: 4.0 x 14.0 x 1.6 Turn-on Input Voltage Ramp up 81 89 Vac 24.5 Watts per cubic inch density Turn-off Input Voltage Ramp down 70.5 78 Low Line AC 90Vac 13 N+1 redundancy capable, including hot plugging Maximum Input Current Arms High Line AC 180Vac 13 (up to 4 in parallel) Inrush Current Cold start between 0-1msec 16.5 Apk Active Current Sharing on main output ORing FET Output load >90% 0.95 Power Factor Overvoltage, Overcurrent, Output load >50% 0.95 Overtemperature protection OUTPUT VOLTAGE CHARACTERISTICS Internal cooling fans (variable speed) Output IC Bus Interface, PSMI compliant Parameter Conditions Min. Typ. Max. Units Voltage RoHS compliant Voltage Set Point Accuracy 12.12 Vdc Line and Load Regulation 11.76 12.48 Optional 1U x 19 Power-Shelf 1 12V Ripple Voltage & Noise 20MHz Bandwidth 120 mV p-p Output Current 9 180 A Load Capacitance 30000 F Voltage Set Point Accuracy 5 Vdc Line and Load Regulation 20MHz Bandwidth 4.85 5.15 1 5Vsb Ripple Voltage & Noise 50 mV p-p Operating Range 0 5 A Load Capacitance 10000 F Voltage Set Point Accuracy 3.3 Vdc Line and Load Regulation 20MHz Bandwidth 3.2 3.4 1 3.3Vsb Ripple Voltage & Noise 50 mV p-p Operating Range 0 6 A Load Capacitance 10000 F 1 Ripple and noise are measured with 0.1 uF of ceramic capacitance and 10 uF of tantalum capacitance on each of the power supply outputs. The output noise requirements apply over a 0 Hz to 20 MHz bandwidth. A short coaxial cable with 50ohm scope termination is used. CB Test Certi cate and Test Report For full details go to www.murata-ps.com/rohs www.murata-ps.com/support CPS D1U4CS-W-2200-12-HxxC.A09 Page 1 of 6D1U4CS-W-2200-12-HxxC Series AC/DC Front End Power Supply OUTPUT CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Remote Sense 120 mV 20% load 88 89.1 Ef ciency (230V) excluding fan load 50% load 92 93.0 % 100% load 88 92.2 Output Rise Monotonicity Overshoot less than 10% for all outputs, no voltage negative between 10% to 95% during ramp up AC ramp up 1.5 s Startup Time PS On activated 150 ms 12V Ramp 1A/s 360 Transient Response 5Vsb Ramp 1A/s 150 mV 3.3Vsb Ramp 1A/s 100 Current sharing accuracy (up to 4 in parallel) At 100% load 7 % Hot Swap Transients All outputs remain in regulation 5 % Holdup Time 100% load 12 ms ENVIRONMENTAL CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Storage Temperature Range Non-condensing -40 70 D1U4CS-W-2200-12-HC4C and D1U4CS- 050 W-2200-12-HA4C models C Operating Temperature Range D1U4CS-W-2200-12-HC3C and D1U4CS- 040 W-2200-12-HA3C models Operating Humidity Non-condensing 10 90 % Storage Humidity 590 Shock 30G non operating Sinusoidal Vibration 0.5G, 5 500 Hz operating Calculated per Bellcore at Ta=30C 400K hrs MTBF Demonstrated 400K hrs Acoustic ISO 7779-1999 60 dB LpAm CAN/CSA C22.2 No 60950-1-07, Am.1:2011 UL 60950-1-2011, 2nd Ed. Safety Approvals UL 60950-1, 2nd Ed. IEC60950-1:2005 (2nd Ed.) w A1:2009, EN 60950-1:2006+A11:2009 +A1:2010 +A12:2011 Input Fuse Power Supply has internal 20A/250V fast blow fuse on the AC line input Material Flammability UL 94V-0 Switching Frequency TBD Weight 4.5lbs (2.1kg) PROTECTION CHARACTERISTICS Output Parameter Conditions Min. Typ. Max. Units Voltage Overtemperature Autorestart 55 65 C Overvoltage Latching 13.1 14.1 V 12V Overcurrent Latching 197 225 A Overvoltage Latching 5.6 6.2 V 5Vsb Overcurrent Brick wall, autorecovery 5.5 6.2 A Overvoltage Latching 3.5 4.0 V 3.3Vsb Overcurrent Brick wall, autorecovery 6.5 8.0 A www.murata-ps.com/support CPS D1U4CS-W-2200-12-HxxC.A09 Page 2 of 6