QPL9097 Ultra-Low Noise, Bypass LNA General Description The QPL9097 is a high-linearity, ultra-low noise gain block amplifier with a bypass mode functionality integrated in the product. At 3.8GHz, the amplifier typically provides 22 dB gain, +34 dBm OIP3, and 1.1 dB noise figure while drawing 50 mA current from a +4.2V supply. 8 Pin 2X2 mm DFN Package The QPL9097 is internally matched using a high- performance E-pHEMT process and only requires four Product Features external components for operation from a single positive supply: an external RF choke and blocking/bypass 3.3 4.2 GHz Operational bandwidth capacitors. This low noise amplifier contains an internal LNA with integrated bypass mode active bias to maintain high performance over temperature. Ability to turn LNA and bypass mode OFF Ultra-low noise, 1.1 dB at 3.8GHz The QPL9097 is optimized for the 3.34.2 GHz frequency 22 dB Gain at 3.8GHz band and is targeted for wireless infrastructure. The QPL9097 is packaged in a 2x2mm DFN. +34 dBm Output IP3 in LNA Mode +37 dBm Input IP3 in Bypass Mode Internally matched Positive supply only, +3.3 to +5V 2x2 mm 8-pin DFN plastic package Functional Block Diagram Applications Base-station Receivers Pin 1 Reference Mark Repeaters / DAS Tower Mounted Amplifiers GND 1 8 V DD Mobile Infrastructure 2 7 RF In RF Out General Purpose Wireless TDD or FDD systems N/C 3 6 GND V 4 5 V BYP SD Backside Paddle - RF/DC GND Ordering Information Top View Part No. Description QPL9097TR7 2500 pcs on 7 reel QPL9097EVBP01 Evaluation Board Datasheet, September 21, 2018 Subject to change without notice 1 of 11 www.qorvo.com QPL9097 Ultra-Low Noise, Bypass LNA Absolute Maximum Ratings Recommended Operating Conditions Parameter Rating Parameter Min Typ Max Units Storage Temperature 65 to 150C Supply Voltage (VDD) 3.0 4.2 5.25 V Supply Voltage (V ) +7 V T 40 +105 C DD CASE RF Input Power, CW, 50, T=25C +30 dBm Tj at TCASE = 125C +142 C Operation of this device outside the parameter ranges given Electrical specifications are measured at specified test conditions. Specifications are not guaranteed over all above may cause permanent damage. recommended operating conditions. Electrical Specifications Test conditions unless otherwise noted: VDD = +4.2 V, Temp.=+25C. Parameter Conditions Min Typ Max Units Operational Frequency Range 3300 4200 MHz Test Frequency 3800 MHz Gain LNA ON, Bypass OFF 19.5 22 23.5 dB Input Return Loss LNA ON, Bypass OFF 12 dB Output Return Loss LNA ON, Bypass OFF 11.5 dB (2) Noise Figure LNA ON, Bypass OFF 1.1 1.6 dB (1) Output P1dB LNA ON, Bypass OFF +14 +15.5 dBm LNA ON, Bypass OFF, Output IP3 +30 +34 dBm Pout=+0 dBm/tone, f=5 MHz Insertion Loss LNA OFF, Bypass ON 2 3 dB Return Loss LNA OFF, Bypass ON 13 dB (1) Isolation LNA OFF, Bypass OFF 17 20 dB LNA OFF, Bypass ON Output IP3 +28 +35 dBm Pin=+3 dBm/tone, f=5 MHz VIH 1.17 VDD V Control Voltage, V , V 1 2 VIL 0 0.63 V LNA ON 50 75 mA Current, ID Bypass ON 5 mA LNA-Bypass (50% Vctrl to 10% RF) 137 1000 ns Bypass-LNA (50% Vctrl to 90% RF) 354 1000 ns Switching Time LNA-OFF (50% Vctrl to 10% RF) 26 1000 ns OFF-LNA (50% Vctrl to 90% RF) 55 1000 ns Thermal Resistance, jc Channel to case 44 C/W 1. Minimum specification listed is guaranteed by design. Not tested in production. 2. Input trace loss de-embedded from noise figure data. Control Truth Table V V State BYP SD 0 0 LNA ON, Bypass OFF 0 1 LNA OFF, Bypass OFF 1 x LNA OFF, Bypass ON Datasheet, September 21, 2018 Subject to change without notice 2 of 11 www.qorvo.com