TAT6254B Fiber To The Home RF Amplifier 47 1000 MHz Applications High dynamic range FTTH RFoG (Radio Frequency over Glass) and GPON FTTH Multi Dwelling Unit TIA Mini-node Product Features Functional Block Diagram Pin compatible with the TAT6254C Single 12 V configuration Low Noise 3.0 pA/rtHz Equivalent Input Noise 14 dBmV/channel RF output at 55.25 MHz Both RF and Optical AGC designs available, continuously variable Low power consumption, 1.2 Watts at 12 V -12 to -2 dBm optical input range Linearity better than 62 dBc CSO and 62 dBc CTB General Description Pin Configuration The TriQuint TAT6254B FTTP SFU Video Receiver Pin Symbol provides a low noise analog interface to CATV receivers 1 TIA IN A and optical triplexers. The TAT6254B is intended for use 2,4 BIAS 1 3,13 NC in single family unit (SFU) analog video fiber to the 5 TIA IN B premise (FTTP) applications. 6 BIAS ADJ B 7 TIA OUT B The TAT6254B exhibits low input noise and distortion 8, 18 BIAS 2 that provides performance margin critical to meeting 9 PA IN B stringent FTTP link requirements, particularly those with 11, 12 PA OUT B all QAM channel loading. It runs on a single 12 volt 14, 15 PA OUT A supply, eliminating the need for an extra ONU power 17 PA IN A supply. The TAT6254B provides automatic gain control 19 TIA OUT A 20 BIAS ADJ A (AGC) to maintain a constant +14 dBmV/ch output to EPAD GND ensure consistent video quality and ease of design. The TAT6254B is fabricated using 6-inch GaAs pHEMT technology to optimize performance and cost. The TAT6254B is pin and functionally compatible with the TAT6254C, though it has significantly increased gain and lower noise for all or near-all QAM deployments. Ordering Information Part No. Description TAT6254B CATV FTTH pHEMT amplifier TAT6254B-EB Evaluation Board Standard T/R size = 2500 pieces on a 13 reel. Data Sheet: Rev D 05/28/2012 - 1 of 7 - Disclaimer: Subject to change without noticee 2012 TriQuint Semiconductor, Inc. Connecting the Digital World to the Global Network TAT6254B Fiber To The Home RF Amplifier 47 1000 MHz Specifications Absolute Maximum Ratings Recommended Operating Conditions Parameter Rating Parameter Min Typ Max Units o Storage Temperature -60 to +150 C V 12 V DD o 6 Device Voltage,V +15 V DD T (for >10 hours MTTF) 150 C J o Thermal Resistance (jnc. to case) 19 C/W jc Electrical specifications are measured at specified test conditions. Specifications are not guaranteed over all recommended operating Operation of this device outside the parameter ranges given conditions. above may cause permanent damage. Electrical Specifications (Per Applications Circuit Herein) Parameter Conditions Min Typical Max Units Operational Frequency Range 47 1000 MHz RF Gain at 553.25 MHz See Note 1. 38 dB Gain Flatness 1.0 dB Tilt See Note 2. 4 dB Equivalent Input Noise 3.0 pA/rtHz RF Output Level 55.25 MHz See Notes 3 & 5. 14 dBmV/ch Output Return Loss 16 dB CSO See Note 4. -62 dBc CTB See Note 4. -62 dBc See Note 6. 33 dB Gain Control Range Power Supply Current 12V 100 mA 1) Gain = 20*log (Z/75) 2) From 47MHz to 1000MHz 3) AGC using 3.3%/ch OMI, output level fixed by external AGC 4) 80 channels analog NTSC 5) Uses 4:1 output transformer 6) With suggested RF AGC application circuit, 25dB with Optical AGC application circuit Optical Input and Triplexer Requirements Parameter Conditions Min Typical Max Units Optical Input Power -12 -2 dBm Optical Modulation Index 3.3 %/ch Triplexer 1550 nm PIN Responsivity 0.875 mA/mW Triplexer 1550 nm PIN Capacitance 0.9 pF Data Sheet: Rev D 05/28/2012 - 2 of 7 - Disclaimer: Subject to change without noticee 2012 TriQuint Semiconductor, Inc. Connecting the Digital World to the Global Network